Mini Spares Articles - Over-boring blocks for 73.0, 73.5 or 74mm diameter pistons by K Calver
I frequently hear the phrase "big-bore engines tend to be unreliable long-term because of head gasket problems". Which is complete rubbish, even when non-Payen head gaskets are used.

These big-bore engines can be supremely reliable - providing the are machined and built correctly in the first place. Something that continually astonishes me doesn't happen even when engines are built by some of the self-proclaimed A-series 'experts'.
05/09/2008

I frequently hear the phrase "big-bore engines tend to be unreliable long-term because of head gasket problems". Which is complete rubbish, even when non-Payen head gaskets are used.

These big-bore engines can be supremely reliable - providing the are machined and built correctly in the first place. Something that continually astonishes me doesn't happen even when engines are built by some of the self-proclaimed A-series 'experts'.

The main problem stems from the fact that when the head is torqued down and compresses the fire ring around the top of the bore, it reduces the internal diameter of the gasket to around 72.5mm across the centreline of the bore - i.e. between the cylinders. This is not much of an issue where 73mm pistons are used since all pistons are a smaller diameter at the crown, and even smaller across the wrist pin axis as they are also slightly ovalised. However, where the larger 73.5mm and 74mm diameter pistons are used, unless steps are taken, the piston crown will clip/hit the gasket where it over-hangs the bore.The obvious and unavoidable conclusion is the head gasket will fail - either quickly or after some time. But it will fail. There are a couple of ways to prevent this from happening, rather than hoping to get lucky. First is to make sure the block is bored using the head gasket to centre the re-bore on rather than the original bore centres.

These original bore centres can be anywhere between spot-on central to the gasket to absolutely miles out. Not much of an issue on the usual over-bore sizes of +0.020", 0.040" or 0.060" - hence the factory's lack of attention to detail at getting the bores set better. So when getting your block bored to take the much larger piston diameters, make sure you supply the company with a head gasket with instructions to centre the re-boring to the gasket, across the centreline/wrist pin axis plane. If they are familiar with or are generally seen as A-series specialists, just ask the question and make sure they are doing this. Where block have already been straight bored out using the original bore centres, position a gasket on the block using several head studs, but especially picking up on the gasket locating stud holes - these are sited at the short stud between cylinders 1 and 2 and long stud behind cylinder 4. These head stud holes in the gasket are 3/8" diameter, all the others are 7/16". With the gasket located in this way you can now asses how much and where the gasket fire ring over-hangs the bore, bearing in mind it will over-hang a little more once clamped down by the head. If you are lucky and there is barely any over-hang and evenly all round the bore, you will get away with it dependant on piston position at top dead centre. If it over-hangs more one side than another, front, rear or side to side, then steps need to be taken to ensure no gasket failures occur because of the piston hitting the fire ring. One option here is to make sure the pistons are sited a short way down the bore from the block face when they are at top dead centre - 0.010" to 0.015" would be plenty. Do a trial build to establish piston to block face distances. If the pistons are less than 0.010" down the bore, then the piston crowns will need machining down to make sure they clear the piston.

The main problem here is that you have to have the pistons fitted to the rods to be able to make the measurement in the dry build. Not everybody has build pins - wrist pins with a section ground down to be a slide fit in the con rod - that can be used as 'floating' pins in the rods/pistons during the trial build. The vast majority of folk will be using the original type interference-fit wrist pin to rod set-up. Also - once the pistons are properly fitted to the rods, not all machine shops are capable of machining the piston crowns with the rods attached to the other end. The answer here is to get the piston crowns machined before they are fitted to the rods.

The best way of doing this is to machine either a reasonable chamfer or a small 'step' in to the piston crown edge to allow for the gasket over-hang.

Importation rules regarding vehicles are very specific: Only those over 25 years in age may be brought in to the USA without compilance to Federal Motor Vehicle Safety Standards (FMVSS).

Author

admin