Showing 1 to 20 of 93

Non genuine replacement part track rod end for all factory mini steering racks. See also C-AJJ1572 for longer type with more thread or GSJ1106 for genuine type. Sold individually.

Do not forget to replace the top plastic bush GSV1095 when replacing this lower felt type bush. From 1985 Rover changed to a plastic bush NAM8563 on the bottom with a different outer steering column shroud.

The dowel that fits in the front hub to locate the steering arms. Bolts for these are 2A4315 and the locktabs are 2K5377.

Sold singly, 2 required per arm

Small split white plastic bush for lower steering column from 1985-96 pre air bag models. Always change the plastic upper bush GSV1095 as well when you do this job.

this is the only steering wheel that will fit the quick release/snap off boss assembly-if you want the standard boss order SWABM--for the snap off boss see SWABS---wheel is 340mm wide(just over 13")

Non genuine gaiter kit with plastic clips for your steering rack is our best seller but see 17H6298 for single gaiter.

17H6298 single gaiter 4.5" long.

BHM7113 gaiter kit 4.5" long.

GR...

The Mini MK2 steering arms were designed to be used with the later model rack that has a tighter turning ratio than the early MK1 rack. A pair of Cooper S thicker arms can be purchased cheaper than a single arm. The angle of all arms from 1967 are sl...

Most new steering racks are now filled with a grease but these oil seals were very neccessary on the older models. This fits the pinion that leaves the steering rack for the inner column to bolt on.

Horn push assembly for the Mk1 Morris Mini, Mk1 Morris Mini Cooper and Mk1 Morris Mini Cooper S.

For Austin cars, see 27H6943. This horn push assembly can also be supplied without a centre emblem, see 27H6945

Non genuine rubber single steering rack gaiters. See BHM7113 for a pair, these are the most common size but see 17H6298 and

17H6298 single gaiter 4.5" long.

BHM7113 gaiter kit 4....

There are 2 of these bolts per arm and the locating rings for them in the hub are FAM6924 and the locktab are 2K5377 and all of these parts were standard fitment on every mini produced.

Torque setting 30 to 35 lb/ft...

All steering wheels pre air bag (twinpoint injection cars 1997 on) should have this shakeproof washer fitted under the large securing nut (ACH6001) and should be replaced every time the wheel is removed.

On all cars with a steering lock there are safety shear bolts on the column which will need replacing if removed. These are the 2 (5/16"unf)bolts 7/8"long thread that hold the steering column bracket to the dash rail. 1.5"(37mm) long overall.Sold sin...

This is a strange shaped nut which locks the bolt which goes through the upper

column bracket which in turn clips to the body bracket. 5/16" unf thread.

On all cars with a steering lock there are safety shear bolts on the column which will need replacing if removed. This is the 5/16"unf 2.0125"thread and stud length 2.70"(68mm)- overall length long bolt that holds the steering column bracket to the c...

Will only fit cars with airbag type steering wheel and column as fitted to twin point cars from 1996 on.

The Mini MK2 steering arms were designed to be used with the later model rack that has a tighter turning ratio than the early MK1 rack. The angle of these arms is slightly different thus allowing the tie rod end to have a little more range of adjustm...

Longer version of BHM7113 about 7.5" long, new and fits all Mini Spares current steering racks from January 2011. Both gaiters are identical.

one kit required per steering rack with plastic clips

17H6298 si...

On all cars with a steering lock there are safety shear bolts on the column which will need replacing if removed. These are the bolts that hold the steering lock halves together.19mm (3/4") long. 2 required par car, but sold individually.

1 2 3 4 5