STEERING ARM BOLT
2A4315

£3.05 exc vat

£3.66 inc vat

In stockIn stock
There are 2 of these bolts per arm and the locating rings for them in the hub are FAM6924 and the locktab are 2K5377 and all of these parts were standard fitment on every mini produced.

Torque setting 30 to 35 lb/ft or 4.1 to 4.8 kg/m.

Sold singly 2 required per steering arm to hub-4 per car

£3.05 exc vat

£3.66 inc vat

In stockIn stock

Recommended usage 4 x 2A4315 to fit one mini.
Front Suspension - Qty 4
Front Suspension, Hubs, Upper and Lower Arms - Qty 4

Recommended products

The dowel that fits in the front hub to locate the steering arms. Bolts for these are 2A4315 and the locktabs are 2K5377.

Sold singly, 2 required per arm

Locktabs for under the steering arm bolts on all minis. Fits either side.

Sold individually

People also bought products

Set of 4 High quality Japanese sealed ball joints.



Developed and tested over a period of three years, the original concept was to manufacture a high quality product, similar to those used on modern vehicles. Unlike the current des...

High quality sealed ball joints from Mini Delta Japan.



Developed and tested over a period of three years, the original concept was to manufacture a high quality product, similar to those used on modern vehicles. Unlike the current ...

This dark woodrim steering wheel requires a centre boss to suit your particular car and is the best value and quality wheel around in its class. Brightwork 3 spoke

centre design.

This woodrim steering wheel requires a centre boss to suit your particular car and is the best value and quality wheel around in its class. Brightwork 3 spoke

centre design.

Mini steering racking fitting kit comprising of 2 U-bolts, 4 nyloc nuts, 2 plastic anti friction stipes, the foam rack to body seal and the half nuts to lock the track rod ends

High tensile nut for swivel pins - supplied in kits GSJ166MS and GSJ166.

Nylon bush for original C.A.M steering racks fitted by Leyland/Rover.

Motalita steering wheel boss for MK1 minis only with green light indicator stalk and centre cap horn push.

For all MK4 minis from 1976 until 1996 air bag models arrived.

Models from 1989 on only have one cancelling pin,match the boss to the existing wheel and remove unwanted pin.

Required to fit Mountney wheels to your Mini. The Mkl adapter Black boss has a built-in horn-push. The Mkll (BOSS/V3) is for cars with the horn on the stalk.

Special shaped U bolt for holding the steering rack in place. Every mini uses 2 of these and make sure you fit the 21A2553 plastic anti friction strips. Sold singly

The sponge dust shield that fits over the splined area of the steering rack as it bolts up against the bulk head. Usually it is sold with the centre part cut but not pushed out, but it pops out easily and is shown on our picture as a reference only. ...

Quickracks-If you are interested in performance driving then you know reaction time from the driver to the car is critical; the time it takes to turn the steering wheel to the desired angle is important! The standard rack is 2.7 turns lock to lock, o...

This woodrim steering wheel requires a centre boss to suit your particular car and is the best value and quality wheel around in its class. Brightwork 3 spoke

centre design.

A bit larger than the MK1 to accept the improved indicator switch this fitted

MK2 and MK3 cars until the introduction of the steering locks.

the classic looking 13" steering wheel from the 1960s and 70s with round holes in the 3 semi dished polished alloy spokes and a leather rim. For black spokes see 33SBLBH or for wooden rim see 353SPW

Horn push assembly for the Mk1 Austin Mini, Mk1 Austin Mini Cooper and Mk1 Austin Mini Cooper S.

For Morris cars, see 27H6944. This horn push assembly can also be supplied without a centre emblem, see 27H6945