£4.71 exc vat
£5.65 inc vat
In stock
£4.71 exc vat
£5.65 inc vat
In stockRecommended usage 1 x 37H8064 to fit one mini.
The sponge dust shield that fits over the splined area of the steering rack as it bolts up against the bulk head. Usually it is sold with the centre part cut but not pushed out, but it pops out easily and is shown on our picture as a reference only. ...
Mini steering racking fitting kit comprising of 2 U-bolts, 4 nyloc nuts, 2 plastic anti friction stipes, the foam rack to body seal and the half nuts to lock the track rod ends
Screw for MK4 (1976) onwards BHM7085 plastic steering cowl, 2 required. Sold singly.
Special shaped U bolt for holding the steering rack in place. Every mini uses 2 of these and make sure you fit the 21A2553 plastic anti friction strips. Sold singly
The sponge dust shield that fits over the splined area of the steering rack as it bolts up against the bulk head. Usually it is sold with the centre part cut but not pushed out, but it pops out easily and is shown on our picture as a reference only. ...
Quickracks-If you are interested in performance driving then you know reaction time from the driver to the car is critical; the time it takes to turn the steering wheel to the desired angle is important! The standard rack is 2.7 turns lock to lock, o...
A bit larger than the MK1 to accept the improved indicator switch this fitted
MK2 and MK3 cars until the introduction of the steering locks.
Bolt for the bottom of the inner steering column to lock it onto the steering rack spline. This is a Rover special fitting bolt with a 1/2" plain shank to fit the inner steering column groove.
As it is an expensive bolt, for any other purpos...
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
The first thing I do when I get a new Mini is to add a steering column adjuster. This bracket lowers the wheel 1" to 3" for a sportier driving position.
Always make sure you release the tension on the steering rack by loosening the 4 nuts o...
Large steering wheel nut for all pre air bag models, and a shakeproof washer 53K3480 must be fitted for safety reasons.1 5/16" spanner size 1.3125" wide (33mm).
A reproduction of the original MK1 steering column plastic shroud, moulded in the original plastic, painted and ready for polishing! Sold only in sets of upper and lower pieces. For MK2 see 8G6035.
Called an anti friction strip this plain looking (plastic) piece of strip is used on all mini steering racks between the U bolt and the rack probably because the U bolt is hard steel and the rack is softer rough cast alloy. See 2A6208 fo...
Quickracks-If you are interested in performance driving then you know reaction time from the driver to the car is critical; the time it takes to turn the steering wheel to the desired angle is important! The stock/standard l/h/d steering rack is 2.7 ...
Plastic upper bush that should be replaced when you have play between the inner and outer steering column. Remember to change the bottom as well whether it be felt or plastic type.
Brand new steering rack less track rod joint ends for Mk2 models 1967 on, with right hand drive steering.
Always replace the dust shield sponge 21A30 between the body and rack where the spindle that locates the inner ...
Mini Spares genuine product-plastic 2 piece casing for the steering wheel cowl was introduced in 1976 which was for the introduction of twin indicator stalks and a different steering lock. Twin point injection cars have different cowling and switches...
Right hand drive steering rack for all sportspack models, 1997 onwards. The rack has reduced lock in order to help with clearance of the larger 6x13 sportspack wheels. Very useful when fitting aftermarket 13" wheels that foul bodywork.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.