Mini Spares Articles - DIAPHRAGM SPRING - Verto types including injection
The Verto/Valeo type diaphragm included the pressure plate in its assembly, much like a 'normal' car set-up. The spring being of the 'finger' type as opposed to the disc spring used on earlier, three-piece assemblies. There were originally three diaphragm specifications using progressively stronger springs - small-bore, big-bore, and Metro Turbo. Later joined by the type used on the injection cars, though most definitely not interchangeable. Initially, the biggest problem was the Turbo ones were never really available on their own. If you wanted one you had to buy a whole clutch/flywheel assembly - the cost exorbitant. Rover originally believed that if the clutch plate was worn out, then the flywheel and pressure plate would be too. It has only been recent times that the diaphragm/pressure plate has been available on it’s own - but not until after the Turbo unit became unavailable. Even that has changed recently with the cessation of the Turbo diaphragm as a service part.
12/08/2004

Part No Applications: GCK371AF, C-AEG422, C-AEG423.

The Verto/Valeo type diaphragm included the pressure plate in its assembly, much like a 'normal' car set-up. The spring being of the 'finger' type as opposed to the disc spring used on earlier, three-piece assemblies..

There were originally three diaphragm specifications using progressively stronger springs - small-bore, big-bore, and Metro Turbo. Later joined by the type used on the injection cars, though most definitely not interchangeable.

Initially, the biggest problem was the Turbo ones were never really available on their own. If you wanted one you had to buy a whole clutch/flywheel assembly - the cost exorbitant. Rover originally believed that if the clutch plate was worn out, then the flywheel and pressure plate would be too. It has only been recent times that the diaphragm/pressure plate has been available on it’s own - but not until after the Turbo unit became unavailable. Even that has changed recently with the cessation of the Turbo diaphragm as a service part.

To add insult to injury there appears to be no easily identifying marks like on the older colour coded ones. It was all done by serial numbers - which weren't recorded anywhere accessible. Totally and utterly confused further by the long series of super-cessions from one number to another depending on which way the wind was blowing at the time, mixing both small and big-bore components up at will.

So to up-rate your small-bore Verto/Valeo clutch assembly, it was really necessary to purchase a new big-bore, non-injection diaphragm/pressure plate assembly to be sure you were getting a stronger spring. The standard 1300 big-bore type would cope with up to 75bhp. Up-rating big-bore engines meant using the Turbo one that would have to do for everything else. Fortunately it was capable of dealing with 1380 'road rocket' power when used with the non-sprung centered standard clutch plate from the earlier pre-Verto/Valeo assemblies. Particularly if combined with the Mini Spares steel flywheel outer section that offered yet further clamping pressure increases through cunning design.

Now, the only way to up-rate the non-injection Verto/Valeo set-up is to use the latest 1300 non-injection Mini diaphragm combined with the Mini Spares Steel Verto/Valeo flywheel section. This set-up provides the same clamping force as the Turbo diaphragm used to do, if not more.

As for the injection cars, trying to up-rate the diaphragm spring clamping pressure seemed impossible. The main problem is the pick-up sensor on the injection models. It reads from a reluctor ring pressed into the back of the flywheel. Unfortunately the designer who came up with the idea was rather single (narrow?) minded in his approach. It didn’t occur to him to use the standard clutch assembly mounting and location points. Oh no, he deemed it necessary to ‘dabble’ – putting the flywheel locating key slot 30 degrees out of position compared to the standard, aeons-old one! This meant that if you bolted a non-injection diaphragm to an injection flywheel section - as would be the case when trying to fit a Turbo diaphragm to up-rate it - the car wouldn’t run. Timing way too far out for the ECU to work. So a little re-alignment is needed, and is easy to do.

Before removing the standard flywheel assembly, remove the starter motor. You’ll see the pick-up sensor positioned just below the starter motor mounting hole. Carefully remove it. If you peer into the hole, you’ll see the flywheel and reluctor ring in its groove – looks like a bunch of big staples stuck to a wire ring. Turn the engine over by jacking one wheel up under the adjoining bottom arm, selecting 3rd gear, and rotating the wheel/tyre. Set number one piston at top dead centre (TDC). Peering into the hole again you’ll see a section on the reluctor ring where there’s a bigger gap between the prongs. Get a reasonably sized marker pen, insert it into the pick-up hole and - keeping the pen as central in the hole as possible – move the pen in until it touches the reluctor ring and marks it. Now remove the flywheel assembly, and look at the reluctor ring to make sure you’ve marked it. If not – put it back in position and try again.

Strip the flywheel down, and lay it clutch face down on a bench. Using a reasonably strong screwdriver, carefully pry each of the reluctor ring prongs around one side only (I do the inside ones) away from the recess’ side. Once all are done, the reluctor ring should pull out easily. If not, go round and check the prongs again. Don’t force it out – you’ll distort it. Once removed, carefully tweak prongs back into their original positions. Re-assemble the clutch/flywheel using the turbo diaphragm. Double check number one piston is at TDC, then fit flywheel assembly to crank, and setting position by inserting the locating key plate. Note it’s not necessary to fit the retaining bolt and torque it all up – this is just for marking the reluctor ring position in relation to TDC. Passing the marker pen through the pick-up hole again, mark the bottom of the recess and remove flywheel assembly again. Press the reluctor ring back into the recess so the two pen marks line up. And that’s it. Re-assemble the whole deal properly, and away you go.

You don’t have to be absolutely dead accurate when marking (i.e. within thousandths of an inch) as there’s an ELEVEN-degree tolerance on the ECU!! And testing hasn’t shown any power increase/loss by artificially advancing/retarding the timing.

Alternatively you could go for the new Mini Spares up-rated and lightened steel flywheel with machined-in reluctor ring and ingeniously up-rated diaphragm/clamping pressure through clever design.

Useful part numbers:
GCK371AF - Turbo diaphragm/pressure plate assembly
C-AEG422 - Steel Verto/Valeo non-injection flywheel
C-AEG423 - Steel Verto/Valeo injection flywheel with machined-in reluctor ring.
For use with NON-injection diaphragm only.

Importation rules regarding vehicles are very specific: Only those over 25 years in age may be brought in to the USA without compilance to Federal Motor Vehicle Safety Standards (FMVSS).

Author

Keith Calver