BOOT BOARD INJECTION MODELS ONLY
CCC113

£69.00 exc vat

£82.80 inc vat

In stockIn stock
Fits injection cars it is identified as it has 2 corner cut outs to fit. Covered in black carpet.

£69.00 exc vat

£82.80 inc vat

In stockIn stock

Recommended usage 1 x CCC113 to fit one mini.
Seats and Trim - Mini 1996-2000 - Qty 1
Seats and Trim - Mini Non Cooper 1993-96 - Qty 1
Seats and Trim - Mini Cooper 1990-1996 - Pre MPI - Qty 1

Recommended products

The bracket fitted to the boot board and is not in any kits.

When a boot board is fitted the following brackets are required

14A9780x2 U shaped for the rear to hold the board

14A9781x2 side bracket with plug for board to si...

People also bought products

Full carpet boot liner kit, completely lines the inside of the boot area.



Not suitable for MPI minis.

This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.

This kit does not include the bracket on the boot board 14A9783

For 7.5 gallon petrol tank cars this is 29" wide with one corner cut. If you are looking for an alternative to this carpet covered wood boot floor, try our plastic load liner EBF100150

FITS STANDARD 10" AND 12"WHEELS made in strong PVC covered felt known as Hardura

This is Rovers tailor made plastic boot liner which fits all cars with the larger 7.5 gallon petrol tank fitted from about 1974 on. Fits over the spare

wheel giving a very sturdy load floor with a recess for polish or small tools etc. If thi...

Black with mirror, optional colour aftermarket sun visor for Mk3 models which were thinner than pre 1965 cars for safety requirements. Will fit cars from December 1965 on. Check out the special clips to hold these visors as they are sold seperately ...

Similar to those fitted as standard on the late Coopers this piece of trimming is purely cosmetic although it may help to eradicate some road noise that might get past the standard rubber gaiter--This is black with red stitching.

Black sun visor less mirror that requires clips both ends but never a standard fitment colour fits cars from Dec 1965. Available as a sought after alternative to the cream colour. The brackets are available as a car set only(4 clips) as SV20...

This bag is made out of "Hardura" which is a heavy PVC with a felt backing laminated to it. When sewn up it will hold the Jack & lever and is all held with the tie Straps. Because the bag is made of heavy material it will not wear through unlike plas...

Ideal for solving the problem of fitting extra speaker's, this speaker board is simple to fit, and well finished speaker holes are oval 6"x9"

The rubber type grip fitted on handbrakes-

will fit any single cable hand brake from 1976 on

Mk1/2 used 13H5541 thinner plastic type--to fit this to pre 1976 early cars you will need to put lots of sticky tape on the h...

Multi purpose square plastic plug/nut for No8 screw size was used on many door fixings and fuse box to body.



Also suitable for Twin Point indicator fixings.

Metal plate switch carrier for 5 square type switches.

127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.

19 piece Trim Kit in Black. Kit consists of 2 door panels,2 check straps, 2 rear quarter panels, 2 door fillets, 2 door bin liners, 2 rear companion box liners, 2 rear wheel arch covers and a rear parcel shelf. Suitable for all saloons with sliding w...

Fitted 1969-77 and 1992-96 originally and white from 1970-96 so see PAM5401BLACK and PAM5401AP. C posts trims changed with MPI or Heritage shells.

These headlinings are held in by different shape/length rods which a...

Metal chromed old type classic handle revived for use on MG variants and then a fashion item on minis. On later cars CMZ312 screw might be required which has a smaller diameter head and longer thread. Length 90mm.

High quality, these handles fit all models with windup windows.



For matching door opening handles and bezel, see MSA1131/MSA1135.

See MSA1129 kit for car set of plain alloy polished handles.

2 outer rings and 2 inner knobs which have to be stuck on.

This is the top of the range spray glue that is used to make all our trim products. We recommend you use spray glue to fit your trim products to your car (where applicable). You can use the glue to fit underfelt and carpets to your floor pan, your fo...