Label | Part No | Description | Quantity | Comments | |
---|---|---|---|---|---|
1 | 22A102 | Casing Number 22A104 - 850cc Cone synchromesh, magic wand | 1 | N.L.A. | |
1 | 22A150 | Casing Number 22A145 - 850cc Cone synchromesh, magic wand with smaller 62mm double roller | 1 | N.L.A | |
1 | 22A364 | Casing Number 22A363 - 850cc Cone synchromesh, magic wand 62mm | 1 | N.L.A. | |
1 | 22G66 | Casing Number 22G68 - 850/998cc Cooper ‘A’ and ‘B’ type remote or magic wand | 1 | N.L.A. | |
1 | 22A1294 | Casing Number 22A1288 - 850/998cc Mini ‘B’ type magic wand | 1 | N.L.A. | |
1 | 22A1286 | Casing Number 22A1289 - ‘A’ and ‘B’ | 1 | N.L.A. | |
1 | 22G385 | Casing Number 22G382 - 850/998cc Mini ‘B’ type magic wand | 1 | N.L.A. | |
1 | 22G188 | Casing Number 22G190 - 970/1071cc Cooper ‘S’, ‘A’ and ‘B’ gear remote type | 1 | N.L.A. | |
1 | 22G331 | Casing Number 22G333 - 970/1275cc Cooper ‘S’, ‘B’ type | 1 | N.L.A. | |
1 | 22A1294 | Casing Number 22A1228 - Non ‘S’, ‘B’ remote type | 1 | N.L.A. | |
1 | 22A1529 | Casing Number 22A1522 - Last ‘B’ type for Mini and ‘S’ 3 synchromesh remote type | 1 | N.L.A. | |
1 | 22G1338 | Casing Number 22G1128 - All 4 stnchro with remote | 1 | N.L.A. | |
1 | 22G2383 | Casing Number 22G1832 - Rod change with small idler bearing | 1 | N.L.A. | |
1 | DAM3755 | Casing Number DAM4818 - Rod change ‘A’ plus with 4 bolt bearing retainer | 1 | N.L.A. | |
1 | BHM5045 | Casing Number DAM2886 - Rod change ‘A’ plus with 4 bolt bearing retainer and stronger idler housing | 1 | N.L.A. | |
1 | BHM5093 | Casing Number DAM5626 - ‘A’ plus with 3 bolt bearing retainer | 1 |
Casing No. | Part No. | Description | Comments |
---|---|---|---|
22A104 | 22A102 | 850cc Cone synchromesh, magic wand | N.L.A. |
22A145 | 22A150 | 850cc Cone synchromesh, magic wand with smaller 62mm double roller | N.L.A |
22A363 | 22A364 | 850cc Cone synchromesh, magic wand 62mm | N.L.A. |
22G68 | 22G66 | 850/998cc Cooper ‘A’ and ‘B’ type remote or magic wand | N.L.A. |
22A1288 |
22A1294 22A1286 |
850/998cc Mini ‘B’ type magic wand 'A' and 'B' |
N.L.A. |
22G382 | 22G385 | 850/998cc Mini ‘B’ type magic wand | N.L.A. |
22G190 | 22G188 | 970/1071cc Cooper ‘S’, ‘A’ and ‘B’ gear remote type | N.L.A. |
22G333 | 22G331 | 970/1275cc Cooper ‘S’, ‘B’ type | N.L.A. |
22A1228 | 22A1294 | Non ‘S’, ‘B’ remote type | N.L.A. |
22A1522 | 22A1529 | Last ‘B’ type for Mini and ‘S’ 3 synchromesh remote type | N.L.A. |
22G1128 | 22G1338 | All 4 stnchro with remote | N.L.A. |
22G1832 | 22G2383 | Rod change with small idler bearing | N.L.A. |
DAM4818 | DAM3755 | Rod change ‘A’ plus with 4 bolt bearing retainer | N.L.A. |
DAM2886 | BHM5045 | Rod change ‘A’ plus with 4 bolt bearing retainer and stronger idler housing | N.L.A. |
DAM5626 | BHM5093 | ‘A’ plus with 3 bolt bearing retainer |
3 SYNCHROMESH
The original Minis gears were known as cone type synchromesh, which had a brass baulk ring fitted to the gear. These were replaced in October 1962 by the conventional type of baulk ring as used today and became known as ‘A’ type gears. ‘A’ type gears were used up until September 1964 when ‘B’ type gears were introduced, which had to be fitted in complete sets if interchanging with exception to the Cooper ‘S’, which had a 22G204 laygear manufactured to accept ‘B’ type 1st and reverse gears 22A1021 and 22G202 respectively.
‘A’ type gears have a much steeper inclined helical cut which is very noticeable when placed side by side. The ‘A’ type 2nd and 3rd gear both run on bronze bushes whereas ‘B’ type run on 26 small rollers per gear. The ‘A’ type 3rd motion shaft (main shaft) has a smaller nose to accept the 1st motion shaft which has a fixed sleeve bearing which is obsolete and not replaceable. The ‘B’ type 1st motion shaft had a free fitting needle roller bearing, which slides in and out freely. Apart from the 22G204 laygear all ‘A’ type laygears had a circlip recess 1/10” from the ends to hold the layshaft bearings in. All ‘B’ type laygears plus 22G204 had the circlip recess 1” in to stop the bearings moving into the gear, but easily sliding in or out when the gear is not fitted.
4 SYNCHROMESH
At the end of 1968 the 4 synchromesh gearbox was introduced, which had all different gears and ratios. The bearing housing at the clutch end of the gearbox case, which housed the 1st motion shaft roller bearing was machined THINNER on the inside of the gearbox case to help accommodate the extra 1st gear.
ROD CHANGE 4 SYNCHROMESH
Beginning of 1973 the remote gear lever housing extensions were replaced by two external rods, hence the name rod change gearbox Internally the three selector shafts were replaced by one.
About 1982 ‘A’ plus gears started appearing. which were identified by having a groove mark in the middle of the teeth on 2nd/3rd gear, 1st motion and 4th gear on the laygear. These were cut at a different tooth angle making the gears (less noisy) with different ratios again.
About 1984 the centre main double roller retainer was changed from 4 holes to 3 holes as the case tended to crack where one of the locating holes for the retainer was drilled.