£28.80 exc vat
£34.56 inc vat
Out of stock
s...
£28.80 exc vat
£34.56 inc vat
Out of stock
Competition type 4 point harness wth 2" wide straps and for colours see
MSA1110 for black and MSA1110RED --for 3" wide strap see C-SSB1000/2
Auto retractable seat belt kit. Sold per seat. The manufacturer states that these belts are direct replacements for the inertia reel type fitted from 1976 including the later pre tensioner type. Not suitable for MK1/2 saloons and vans/pickups due to...
With headrest-this fixed back traditional bucket seat is the entry level
version of Cobra seats and has dep sides and a low back to ensure comfort and support without the restrictions of a larger seat. Black vinyl and no piping-
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
Fixed back for fast road this is Cobras New Clubman seat which still represents
good value with its massive leap in quality and design. Integral headpad and shoulder supports,deep sided bucketed supports,integral lumber support and four poin...
without headrest-this fixed back special narrow seat was especially designed to work where space is at a premium -Its low back is ideal for sports cars and vintage.Seat can bolt to floor if accessable or on Cobra seat frames--The seat is about 18" wi...
FIA certified and approved for motorsport it is lightweight and has compact styling. Slotted for use with competition seatbelts and the ultra strong construction has reinforced shoulder and side pads. In black, now comes with The option of using FIA ...
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
MK3 Black Mini door and rear quarter trim(4 piece kit) in vinyl as per original twin line pattern per Mini and CooperS but for cars after May 1973 where the rear quarter panel trim shape did not have a cut out for the ash tray mount and if you look a...
Cream with crackle finish sun visor fitted as standard from December 1965-69 but will fit Mk3 on if required. With mirror for passenger side. For a car set of clips see SV2021
Mk1/2 1965 on cream crackle SV2017C
Mk3 196...
Black with mirror, optional colour aftermarket sun visor for Mk3 models which were thinner than pre 1965 cars for safety requirements. Will fit cars from December 1965 on. Check out the special clips to hold these visors as they are sold seperately ...
Car set (one pair) rear wheel arch vinyl trim covers.
Original MK1/2 finer grain wheel arch cover-heavier grain pattern is WAC3025A although not much diffferent and never noticed.
Printed circuit board for pre 1989 cars with Smith's 2 clock gauge clusters. These have been unavailable for many years but have now been remade exclusively for Minispares.
Although not FIA approved this is made by the top roll bar company Safety Devises. Do not get caught out buying cheap inferior types of unknown quality.
Comes in Black.
Rear Alloy Brightwork moulding for the interior rear companion box R/H.
deleted for EMB10013 plastic in 1991
127cm long and 43cm wide this is enough leather cloth trim that fitted S and deluxe models on the upper and lower facia plus the winscreen A posts. Fitting instructions are included but no glue.
Required to fit Mountney wheels to your Mini. The Mkl adapter Black boss has a built-in horn-push. The Mkll (BOSS/V3) is for cars with the horn on the stalk.
This red carpet is the correct moulded shape with insualation material attached where appropiate for that smart fit over the gearbox tunnels etc.For vehicles pre 1972 with remote or magic wand type gear levers you will therefore have to cut this hole...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.