(¥103) £102.54 exc vat
(¥123) £123.05 inc vat
In stock
Does not include 2 front wheel cylinder bridging pipes pipes HF10 for drum brakes. These kits or pipes are at least 35% off retail
(¥103) £102.54 exc vat
(¥123) £123.05 inc vat
In stockRecommended usage 1 x GB4992 to fit one mini.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Same steel braided pipes but includes the clutch pipe for Verto type clutch.
Please be aware the fronts are sided, the deeper threaded hose fits the right hand side, the shallower hose fits the UK passenger side.
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
Brass 2 way brake union that bolts on front subframe.
This holds the brake light switch(C16062A) on single line brakes and fits into the 2 way union where the front hose bolts on the other end. Later cars with no switch use C5192A.
All MK1/ MK2 Minis including all Cooper and "S" versions plus MK3"S" only.
This valve was fitted to every MK1/2 car including Cooper and "S" and the MK3 Cooper "S" only.
All other MK3 versions 850/998/1100 use 21A2031 w...
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis.
Copper easy bend 10" long metal pipe with male and female end fittings to fit between rear wheel cylinder and flexible hose on dry suspension models. These pipes are retail less 35% discount at least to keep prices viable.
HYDROLASTIC WITH SERVO and includes 2 front wheel cylinder bridge pipes if required. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good idea to check your metal brake line...
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
This Genuine AP 3 way connector was used on the diagonal split braking system joining the front brake pipes to the main line system on both sides of the car, hence 2 fitted. On later dual line cars, with the pressure valve on the bulkhead (1978 on), ...
Pair of front only braided steel hoses. Please be aware these are sided, the deeper internal threaded hose fits the right hand side, the shallower hose fits the passenger side.
These do not fit Portugese Mokes as they need 2 shallo...
Pair of steel braided rear hoses only. See C-AJJ4031B also for safer pro set up.
Master cyl to servo for rhd 30-32". Also brake line for master cylinder to "T" on LHD models. 32" in length. Also clutch master cylinder on L/H/D (usually 32-34" long) but this easy bend pipe will fit all. These pipes are retail less 35% discount at ...
10" long pipe with 2 male ends used on front drum brakes to join the wheel cylinders. Made in easy bend copper for long life. These kits or pipes are at least 35% off retail.
see 21A1206 for pre bent steel rh
Rear Braided brake hose set, with banjo union bolts and howver you need some tie wraps to hold hose to arms, runs from Radius Arm to Rear Cylinder, replaces both standard metal and rubber hose. No modifications are required and is of special interest...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.