£130.50 exc vat
£156.60 inc vat
In stock
IF A MAIL ORDER OR INTERNET ORDER IS PLACED FOR THIS ITEM IT IS AT YOUR (THE CUSTOMERS) LIABILITY, WITH REGARDS TO DAMAGES.
£130.50 exc vat
£156.60 inc vat
In stockRecommended usage 1 x 14A7056 to fit one mini.
This windshield has a very slight tint all over, barely noticeable but enough to reduce glare and make the car cooler inside. Fits all years and models of Mini
except twin point cars which have built in mirror base. IF A MAIL ORDER OR INTER...
Top tint Front Windscreen.
This is a tinted front windscreen with a heavy green top tint.
Clear laminated windscreen for all minis except Twin point injection cars 1996
on which had a special screen with built in interior mirror base.
IF A MAIL ORDER OR INTERNET ORDER IS PLACED FOR THIS ITEM IT IS AT YOUR (THE CUSTOMERS)...
Front door sliding type front window glass. MK1/2 plus all mini commercial type derivatives
Rear screen seal for mk1 cars which had the smaller rear window 1959-1967.
Front and rear screen with chrome plastic insert.Saving nearly 15% on cost of individual partts
Sliding window type weatherstrip kit R/H
kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...
Rubber seal for all mini windshields. Uses locking strip 24A1466(chrome) or 37H8052(black.) REMEMBER YOU MUST FIT THE RUBBER TO THE BODY FIRST. DO NOT USE THE STRING METHOD BECAUSE IT STRETCHES AND TEARS THE RUBBER.
There is a later wider r...
Most minis have a chrome coloured plastic insert in the windscreen rubber but
some owners in hot countries prefer this black one, which some claim is less prone to shrink or go off colour.
Finishing clip in brightwork (chrome colour)for 24A1466MS locking strip in windscreen and backlight rubbers.
The MK1/MK2 Mini not only has a smaller rear side quarter window than the MK3 but also the rubber seal is cosmetically different. The only seal available for years was the MK3 which has a grain texture on the inside edge. Now in stock are very good r...
Genuine Mini Spares quality product. For Mk1 cars use 14A8744
For Pickups you will need to cut and shorten either seal and make sure the join is at the bottom. The extrusion is the correct shape.
This seal is the best ...
Front door sliding type window rear square glass, as fitted to MK1/2 saloons plus all vans and pick-ups
Sliding window type weatherstrip kit L/H.
Kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with...
The plastic chrome insert for fitting in the windscreen and backlight rubbers of all minis. You will require TOOL02 to fit these.
Non genuine double skin MKI boot lid. Always fix your swinging number plate and hinges on for dummy fit and alignment before spraying.
This is the only double skin bootlid avaialble.
The Genuine double skin Mk2 type 8G927...
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
Called the rear bonnet seal it actually sits in the windscreen front scuttle panel on all minis up to 1991. This is the shape and size neoprene foam seal that we have found works best and has an adhesive backing to make fitting easier and less messy.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.