£199.50 exc vat
£239.40 inc vat
In stock
This is the only double skin bootlid avaialble.
The Genuine double skin Mk2 type 8G9270 introduced in december 1966 is no longer available. Fit14A9838 Boot board for protection.
Need new cables for the boot lid? See 14A6740.
£199.50 exc vat
£239.40 inc vat
In stockRecommended usage 1 x 8G9270MS to fit one mini.
Up until December 2003 we would have been embarrased to sell the only chrome
boot hinges available. They were bad fitting, looked poor quality and had so much play in them they were totally useless. But along came a set which does fit and is...
This liner was found on many deluxe Minis. The black fiberboard is held on by chrome screws and upholstery washers. Put it on any year Mini.
The original T shape boot handle as fitted to the bootlid of MK1/2 plus vans and estates except the wooden variety....
uses the ADA3817 type of seal, hole will need cutting to suit the shaft of the handle
These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car
37H3043 can be u...
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Non Genuine metal battery box. always going rusty owing to the location of where it is fitted. Requires welding in place and preferably painted or a protective coat. Remember to check if the battery cover, strap and clips need changing. Popular afte...
The boot floor (trunk of the Mini) has always been an area with a great potential to rust. Not only is it often exposed to battery acid but typically water collects there and rust results. BM Heritage produce a sub assembly from original tooling tha...
Genuine metal battery box. always going rusty owing to the location of where they are fitted. Requires welding in place and preferably painted or protective coat of some kind and remember to check if the battery cover, strap and clips need changing...
Key barrel set for Mk3 onwards door handles and boot handles.
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.
boot board 32" wide for early cars with smaller 5.5 gallon tank
A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).
Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...
This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
If you want your door and bootlid to have new or matching keys this is the easy way. The standard set includes two barrels with matching keys. This is only suitable when you require a drivers door and boot handle to match on MK1/2 cars only. This fit...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.