£102.82 exc vat
£123.38 inc vat
In stock
£102.82 exc vat
£123.38 inc vat
In stockRecommended usage 1 x GB5000 to fit one mini.
Genuine AP car set of 4 brake hose for cars with front disc brakes. If you are changing one through wear and tear it is a good idea to change the whole set and save money with peace of mind about your brake system. Securing nuts included
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.
These pipes are retail...
Split diagonal saloon without 4 way valve, fits L/H/D and R/H/D.
Van and Estate version is GB5007.
You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is ...
Single line L/H/D with servo-dry suspension. If you have a drum brake mini then this kit will require 2 front wheel cylinder to wheel cylinder pipes HF10
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
From 1989 minis which have the brake servo built into the master cylinder and it is very difficult to work in the engine bay, especialy clutch changes because of the extra room taken up by this dual cylinder. By replacing the 2 metal brake pipes from...
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
Male metric brake union as used on front to rear PDWA valve and later master cylinders. Pipes should be double flared.
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
Same steel braided pipes but includes the clutch pipe for Verto type clutch.
Please be aware the fronts are sided, the deeper threaded hose fits the right hand side, the shallower hose fits the UK passenger side.
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis. These kits or pipes are at least 35% off retail.
This holds the brake light switch(C16062A) on single line brakes and fits into the 2 way union where the front hose bolts on the other end. Later cars with no switch use C5192A.
All MK1/ MK2 Minis including all Cooper and "S" versions plus MK3"S" only.
This valve was fitted to every MK1/2 car including Cooper and "S" and the MK3 Cooper "S" only.
All other MK3 versions 850/998/1100 use 21A2031 w...
Brake hose for models with disc brakes.Beware of very cheap imports. We all believe that our life often depends on our braking system. But how can you tell when "it's good enough"? The flexible rubber brake hoses are a prime area for concern. The ho...
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.