£37.50 exc vat
£45.00 inc vat
In stock
£37.50 exc vat
£45.00 inc vat
In stockRecommended usage 1 x ROCKERCVR05 to fit one mini.
This thermostat housing fitting kit, suitable for all single tier thermostat housings. Comes with new studs, nuts, washers and Klinger thermostat housing gasket
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
Mini cork Rocker cover gasket, suitable for all Minis and A series engines except those with 11 stud heads (see part number GUG5038VC). A must have replacement item when adjusting rocker clearances. see GUGG705009EVO for sil...
This 5/8unf steel hexagonal head blanking plug was made for the inlet manifolds where the servo union can be fitted, plus blanking off the thermal transmitter hole under the thermostat. Uses 1B3664 washer ----------please note this will ...
A simple way to dress up that engine compartment while at the same time insuring all the proper hardware is in place. A kit includes 2 each of British made chrome sleeve nuts, spacers and special cup washers, Fits all A & B series engines.
F...
Payen,stamped BK450, original standard composite reinforced gasket used on all large bore engines by Rover including Metro and MG Turbo and is an exceptionally good gasket.
Asbestos free with copper type sealing rings. Compressed volume is ...
The intake/exhaust manifold should be secured to the head with brass nuts and these very thick washers. These washers are intended to not only spread the clamping action but the thickness allows them to absorb the heat without deforming! Takes 4 per ...
Standard alloy thermostat housing. If you want the larger bore type as used on the Cooper with a sandwich plate see PEQ10019 housing GRH1140.
Requires thermostat gasket GTG101MS or GUG705558G...
Forget all the universal shape gaskets available - this is the original correct shape made out of thick gasket paper.
This is the longer type cylinder head adaptor tube which allows fitment of the by pass hose without removing the head. The shortened hose GZA2083 slides up the tube and then back down on the water pump tube. Frequently rusted on old head...
On late A plus engines the factory changed over to bolts rather than a stud on thermostats with a sandwich plate underneath them, all are interchangable as the cylinder head threaded hole was standard. 5/16"unc 2.5"long(2 & 9/16" to be exact (63.5mm)...
Only available as a cork version now this has the cut out for the 11 stud cylinder heads as used on the original Cooper S variants.
Thermal transmitter fitted in the cylinder head from 1970 on until its demise on the 1990 Coopers this part was the same as GTR143. One number was original fitment and the other supplied as the spare part by Unipart.
Fits 998 1275 and cooper...
Ribbed fins on a slant similar to MG Metro original equipment.This is the traditional dress-up for the engine compartment! Great looking, easy to clean and helps cool engine oil. Red plastic Cap is included, but is not the original colour red, we can...
Replace with new camshaft,it's almost too easy to overlook during a rebuild. Camshaft bearings are pressed into the block and thus are usually done by a machine shop. You would not rebuild an engine without replacing the rod bearings, so why not the ...
Race quality single piston ring pack for Mini Spares Evolution Pistons which also fits Mega and Omega pistons. This uses 3 piece oil ring 4mm and 2 of 1.2mm compression ring.
sold per piston so 4 packs required per engine
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.