£270.00 exc vat
£324.00 inc vat
Special order
good value with its massive leap in quality and design. Integral headpad and shoulder supports,deep sided bucketed supports,integral lumber support and four poin...
£270.00 exc vat
£324.00 inc vat
Special orderRecommended usage 2 x SEAT03V to fit one mini.
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
Universal to fit many vehicles and definately the mini for all Cobra seats but beware if your original seats lock down to the floor as a safety requirement. These do not lock down. The MOT testers in the UK could fail you if yours were originally th...
The Cobra Classic is a low back bucket seat designed for fast road use in modified saloons and sportscars. It's deep sides give firm lateral support and the low density foam padding assures a comfortable ride. Vinyl covered seat is 20" at it's widest...
Fixed back for fast road this is Cobras New Clubman seat which still represents
good value with its massive leap in quality and design. Integral headpad and shoulder supports,deep sided bucketed supports,integral lumber support and four poin...
Universal to fit many vehicles and definately the mini for all Cobra seats but beware if your original seats lock down to the floor as a safety requirement. These do not lock down. The MOT testers in the UK could fail you if yours were originally th...
Fixed back for fast road this is Cobras New Clubman seat which still represents
good value with its massive leap in quality and design. Integral headpad and shoulder supports,deep sided bucketed supports,integral lumber support and four poin...
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
If your vehicle had a seat that locked to the floor it is an MOT requirement that you fit that type of fitting seat back in for safety requirements. This seat frame will allow you to fit the Cobra range of seats to your mini.
See [link]SEAT1...
Ideal for solving the problem of fitting extra speaker's, this speaker board is simple to fit, and well finished speaker holes are oval 6"x9"
Works Dash for LHD cars.
The later type more common dashes as used on the classic works Monte Minis and rally cars from ST Abingdon.
In crackle black finish.
Attaches to top and bottom parcel shelf rails either side...
Although not FIA approved this is made by the top roll bar company Safety Devises. Do not get caught out buying cheap inferior types of unknown quality.
Comes in Black.
MK1/2 style pattern door and rear quarter black vinyl trim kit for MK3 on
These are the 4 major parts that can give your car a fresh look- only fits wind up window type doors as fitted to MK3 range mid 1973 on , without ash tray facility in...
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
If you have twin original 5.5 gallon tanks this 26" wide boot board is the one for you.
Lower moulding clip for wind up window mouldings..4 PER SIDE required but sold singly-Fits CZH1666/7 and PAM1014/5
Also used for 24A1169 glove box moulding MK1/2.
Moulded black carpet set for Rod change change with soundproofing attached where appropiate.
These fit correctly and snugly in your car over the tunnels etc for that professional look. 2 rubber front foot pads and on rear carpet has reinforc...
MK1/2/EARLY MK3. 3 position spring loaded type. Comes with barrel.
For barrel only use part number 24G1345.
Our own tailored over-mat set for front and rear with the union jack emblem that used to be our trade mark before we changed to the love heart mini logo.
This 10 piece handle set is exactly the same kit as sold by every other mini specialist is in bright alloy (not polished alloy as per our other superior kit MSA1129) and consists of two of each of the following, door openers, window winders and their...
This board is vinyl Covered and sits on the rear parcel shelf just under the backlight screen and often gets wrecked by leaky rubber seals around your rear screen. This parcel shelf board will only fit cars up to 1996 because MPI cars and Heritage MK...
See also PAM5401LNG and PAM5401AP
These headlinings are held in by different shape/length rods which are NOT included but we do include the rear corner cloth side sections between the rear side window and backlight ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.