WIRELESS PROGRAMMABLE 123 ELECTRONIC DISTRIBUTOR P...
C-27H7776

($345.00) £345.00 exc vat

($414.00) £414.00 inc vat

In stockIn stock
If you want to tune your engine, or you have an engine for which there is no standard distributor available.....the new 123\TUNE is the answer!



123ignition is proud to announce the first fully programmable wireless ignition! Contr...

($345.00) £345.00 exc vat

($414.00) £414.00 inc vat

In stockIn stock

Recommended usage 1 x C-27H7776 to fit one mini.

Recommended products

100% silcone translucent outer sheath, 8mm lead set with stainless steel wire spiral bound wire giving instant and greater resonance, Kevlar fibre core and a ferromagnetic layer for EMC suppression by Luminition. Top end of ignition lead sets.

Original mini coil fitted to all cars up to 1983.

3ohms

NOT for ballast type ignition systems.

Our research, sales and feed back shows Intermotor coils to be the best available for the mini.

Original type coil bra...

People also bought products

for 23/25D distributor but see [link]47H5250[/link} for resin type upgrade with 3m of wire as opposed to every aftermarket type analysed with only 1.5m of wire.

its worth paying extra for the condenser and rotor arm [link]GRA101]/link]

this is the original mini distributor cap where the leads were secured by screws and was fitted to the 25D range of lucas distributors. This cap had side entry leads [link[GHT101]/link] and is now only available from one or two manufactures owing to ...

These points were fitted from 1974-80 when the distributors became a 45D type,

the distributor cap shape changed also to GDC136 and likewise rotor arm GRA2114 and condenser GSC2109.

Wiper Swithch MK1/2/EARLY MK3 blade type switch for using to convert to 2 speed wipers when current 2 speed wiper motor is used.

Rectangular grey plastic with white plastic interior lamp was fitted to minis from 1974 until 1985. 4.25" long and 1.75" wide. From 1984 on Rover recessed the lamp AFU4092 into the headlining. Fitted with GLB239 bulb. The le...

One pair of S6007 halogen driving lamps 135mm wide by 35mm deep approximately plus a pair of XBU10046 stainless steel brackets. The MONTE3 kit is double these parts.

Brand new Inertia starter with the correct 9 tooth pinion for all minis up to the fitment of the pre engaged type in 1984/5. Do not fit the 10 tooth starter sold by many as it can ruin the ringear or the bendix. Other leyland cars used 10 teeth such ...

Kit includes 2 original rear lower lens in white with reflectors plus 2 upper lens in white for the modern day look. Included are the 4 bulbs required to make the kit legal.

The lens seals are available individually as XFH100460...

IGNITION BARREL TO FIT 13H337 SWITCH. MK1/2/EARLY MK3. ONE BARREL,TWO KEYS

This front turn lamp assembly was used on all Mkl & Mkll Saloons, all Vans and Pick-Ups. It is also an easy installation on later cars seeking that proper sixties look. Includes amber glass lens, chrome surround and rubber boot. The clips to hold thi...

Fitted to cars with the reverse lens built into the rear lamp which became standard in 1976, this is the Right hand seal between the lamp and the car body.

The headlamp bucket is isolated from the body with these rubber seals/gaskets.

Fitted to cars with the reverse lens built into the rear lamp which became standard in 1976, this is the L/H seal between the lamp and the car body.

Made in the UK. Correct fitting stainless steel type with screw and washer at a special low price for any Lucas or Wipac headlight including injection cars.

A headlight trim ring is only the starting point of a good looking car, but you have...

Headlamp sundries kit.

Includes two adjuster screws, plastic nutserts, pullback spring. Two kits are required per car.

This is known as a metalastic type bush as it is metal on the outside and inside with a layer of rubber between. Used on the rear rod change gearbox as a stabiliser bush for the rod change it is also used on our rear anti roll bar kits where appropri...

Pair of Chrome WIPAC spotlights. 135mm in diameter, 60mm deep with covers. The lamp is nearly all forward of the mounting bracket making it great for fitting in front of mini grilles. Bulbs are H3 type 55 watts GLB453.

Thermal transmitter fitted in the cylinder head from 1970 on until its demise on the 1990 Coopers this part was the same as GTR143. One number was original fitment and the other supplied as the spare part by Unipart.

Fits 998 1275 and cooper...

A plastic lamp spade connection with sidelight bulb aperture for use on sealed beam units only. Uses a GLB501 capless bulb. The mini clubman used sealed beams but had independant side lamps and therefore had an equivalent unit less the s...

Black wiper arm for R/H/D with a hook type fitting introduced in 1990. This uses an 11" blade GWB911 made by Bosch which is the best we have found. Sold singly. Will fit any cars from 1970 on with correct blade.