(39,44 €) £39.44 exc vat
(47,33 €) £47.33 inc vat
In stock
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres and 5.5 gallon tank see CCC115 or CCC115A
For use with boot boards CCC110, CCC111 and CCC112. CCC115 original 5.5 gallon tank to 1974 with 10" wheels upto 145 tyres
CCC115A for 165 tyres with 5.5 tank
CCC115B for 145 tyres and 7.5 tank
CCC115C for 165 tyres and 7.5 tank
(39,44 €) £39.44 exc vat
(47,33 €) £47.33 inc vat
In stockRecommended usage 1 x CCC115B to fit one mini.
If you have twin original 5.5 gallon tanks this 26" wide boot board is the one for you.
For 7.5 gallon petrol tank cars this is 29" wide with one corner cut. If you are looking for an alternative to this carpet covered wood boot floor, try our plastic load liner EBF100150
boot board 32" wide for early cars with smaller 5.5 gallon tank
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to sit on except elf/hornet
14A9782x1 centre bracket with support ...
The special pointed shape buffer locates against the boot board of Cooper S and variants where a factory type boot board is fitted.
L/H BOOT BOARD SIDE BRACKET FOR 7.5 GALLON TANK.
Key barrel set for Mk3 onwards door handles and boot handles.
L/H BOOT BOARD SIDE BRACKET FOR 7.5 GALLON TANK.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).
Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...
This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
If you have twin original 5.5 gallon tanks this 26" wide boot board is the one for you.
Mk III Chrome boot handle as fitted to all saloons from 1970 on. Includes 2 keys and paper gaskets.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
Do not forget to replace this little rubber seal that stops water getting into the boot lid via the handle hole. For sliding window type cars the door locks use ADA3817.
On mk3 models the small door gasket on the Mk3 wind up window door hand...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.