£39.56 exc vat
£47.47 inc vat
In stock
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres see CCC115
For use with boot board CCC111.
CCC115 original 5.5 gallon tank to 1974 with 10" wheels upto 145 tyres
CCC115A for 165 tyres with 5.5 tank
CCC115B for 145 tyres and 7.5 tank
CCC115C for 165 tyres and 7.5 tank
£39.56 exc vat
£47.47 inc vat
In stockRecommended usage 1 x CCC115A to fit one mini.
For 7.5 gallon petrol tank cars this is 29" wide with one corner cut. If you are looking for an alternative to this carpet covered wood boot floor, try our plastic load liner EBF100150
The bracket fitted to the boot board and is not in any kits.
When a boot board is fitted the following brackets are required
14A9780x2 U shaped for the rear to hold the board
14A9781x2 side bracket with plug for board to si...
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
This kit contains all the brackets and mounts required for fitting Minis with 10/12" wheels or with 145 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres and 5.5 gallon tank se...
The special pointed shape buffer locates against the boot board of Cooper S and variants where a factory type boot board is fitted.
bracket for boot board R/H on 7.7 gallon tank and on both sides for 5.5 gallon tank when 165 tyres fitted
Taller centre boot board bracket for when wider 165 tyres are fitted to the spare wheel. Supplied with the rubber and pin.
MkI aluminium boot lid "skin only" panel. This panel is produced off the original tooling, ensuring good panel fit and integrity. Following the pressing of the panel it is hand finished by Heritage craftsmen, to ensure the highest panel quality.
Tank strap bracket welded to the rear of the boot floor which the single diagonal tank strap 21A2838 attaches to.
Key barrel set for Mk3 onwards door handles and boot handles.
Taller centre boot board bracket for when wider 165 tyres are fitted to the spare wheel. Supplied with the rubber and pin.
This very heavy duty bonnet strap is a excellent reproduction of the original factory Special Tuning department special. A copy of our Tan leather strap, but now available in black.
3.3mm thick from the tanneries for use on horse bridles,wit...
Full carpet boot liner kit, completely lines the inside of the boot area.
Not suitable for MPI minis.
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Round spare wheel clamp with bolt for fitting in the boot to the spare wheel boss as fitted to Mk1 minis. See 88G479 for the boot floor boss that this clamp screws into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
Full Mk1 door handle set with 2 front door locking handles and boot handle with matching keys.
MKI boot lid manufactured by British Motor Heritage. Always fix your swinging number plate and hinges on for dummy fit and alignment before spraying.
The double skin Mk1/2 type 8G9270 introduced in december 1966 is only availabl...
boot board 32" wide for early cars with smaller 5.5 gallon tank
A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).
Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...
This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
This kit contains all the brackets and mounts that were fitted on to the floor on original Coopers, Wolseley Hornet and Riley Elf with boot boards fitted as standard.
This kit does not include the bracket on the boot board 14A9783
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Not just a skin, but a complete MKI boot lid with inner skin. Lightweight, rustproof and well finished.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.