(5,92 €) £5.92 exc vat
(7,10 €) £7.10 inc vat
In stock
(5,92 €) £5.92 exc vat
(7,10 €) £7.10 inc vat
In stockRecommended usage 2 x GDG233 to fit one mini.
Metal CV gaitor ties for the outer CV gaitor, slim in design in order to give maximum clearance between CV and hub
One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows an...
Hardy Spicer Adapters to convert pot joint output shafts to fit a hardy spice coupling (will also fit the Quaife ATB)
Metal CV gaitor ties for the outer CV gaitor, slim in design in order to give maximum clearance between CV and hub
Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.
Genuine Mini Spares Heavy duty gaiter kit as supplied with our GCV1013 cv joint, contains rubber gaiter grease and metal clips. We consider this the best available with a special shape to stop rubbing or soiling.
Sold singly-2 r...
Non genuine aftermarket only as the genuine originals are obsolete.
These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle; this is ...
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the right hand longer one.
Heavy duty needle roller type coupling with plastic ends. The very early Minis used the rubber joint drive couplings GCD101 to eliminate harshness from being transmitted to the passenger compartment. Over the years the rubber will separa...
There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number GFK3431.
Sold Individually.
In board CV joint(pot joint) gaiter kit with plastic clips and grease.
Non Genuine item many sell as GSV1073.
The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one ver...
Hardy-Spicer coupling was fitted to the Cooper "S" and all automatic varieties pre Pot joint(inboard cv joint) This U-joint assembly slides onto the driveshaft and bolts to the Cooper S output shaft flange. The U joint fitted to these joints is the s...
Special Tuning hit upon this idea to stop the driveshafts breaking on their rally cars. Do away with the large circlip groove where it broke and weld a spacer on the shaft to locate the CV joint in position. The works department also reduced the stee...
Rubber U-joint for yoke-type driveshafts. These are the only new supply available except for QL5000 alternative.
The very early Minis used the rubber U-joint drive couplings to eliminate harshness being transmitted to the passen...
Inboard CV (pot joint) splitting tool used to remove the constant velocity joint from the gearbox by way of driving this wedge-like tool between joint and gearbox. Does not remove joint from driveshaft.
Top quality nut unlike many sold with CV joints from china.
For genuine nut See BTA249 also. Sold singly
Allegro CV joint. These are the larger Allegro CV joints that some competition cars use, they fit Mini hubs but need the larger driveshafts C-BTA1266.
Front hub nut that screws onto the CV joint of all early minis with drum brakes plus all standard cooper 997/8 models. 1 1/8, 1.125" AF nut size although 28mm width have been seen. The washer for this is 2A7323.
Special grease for Cv joints and any homokinetic joints. Enough for one joint only.
Steel driveshafts with original circlip holes, ensure that the cv circlip clicks fully in both shaft and cv joint.
These are upgraded to stop the ends twisting off. Available for rod change also as C-BTA1264 SOLD AS A PAIR
One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows an...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.