SPACER FOR LOWER DAMPER WHEN A BOLT IS USED
21A2694

£1.80 exc vat

£2.16 inc vat

In stockIn stock
THE LOWER DAMPER PIN WAS SOMETIMES REPLACED BY A BOLT AND THIS WAS THE SPACER USED TO PUT THE DAMPER IN THE CORRECT SPRING. C-AJJ3361 LOWER PIN WAS USED MORE COMMONLY WITH BUILT IN SPACER.

£1.80 exc vat

£2.16 inc vat

In stockIn stock

Recommended usage 2 x 21A2694 to fit one mini.
Front Suspension - Qty 2

People also bought products

Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.

Original cone...

Genuine Mini Spares UK made complete joint with the following specifications,

correct dimensions and shape of pin and ball in EN24T, using correct spec grease,

genuine original shape cup using correct material (21A423MS...

Genuine Mini Spares UK made joints are complete with the following specifications, correct dimensions and shape metal knuckle in EN24T, with the genuine cup made in original material and correct shape (21A423MS) and an upgraded poly boot...

Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).

Tie rod extra hard rubber bush, harder than standard.

You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.

In theory the outer ones should be harder for rigidi...

Mini Spares quality suspension kit includes all four adjustable alloy trumpets and knuckle joints plus the two extended rod struts required for the rear. Many people will advise you, why you should consider upgrading to the genuine classic "Hi/Lo" su...

Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.

Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...

one piece forged lower rod end arms

unbelievably at this price they are not the welded type as sold by many of our competitors

Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...

Angled grease nipple for the upper arm on the front suspension of all Minis

importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...

Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...

A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.

From November 2003 they have been made from a s...

Koni Shocks Possibly the best name in shock absorbers, and they're available for the Mini! 20% uprated over Rover standard spec shocks and rebuildable. the adjustment is for fluid degradation rather than performance increase, Adjusting damp...

Genuine Mini Spares part improved from original for the R/H upper mounting point of your damper(shock absorber) and fit 14A6948 captive nut plates for upper bolt fixings . For lowered suspension use C-AJJ3359

These cone springs will require Hilo adjustable suspension as they sit higher than the originals.Containg an anti fade property and shape which helps them going off during racing and giving hopefully a season of racing before replacement. A softer ro...

Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.

HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.

Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...

Lower arm bush for pre 1966 cars. The lower arm had a straight hole whereas the later cars from 1966 on had a tapered hole and used 21A1882 bush with a metal sleeve in. This bush has no inner sleeve and it was discontinued in 1966. Sold ...

Each Hi-Lo Suspension Kit Includes one pair of Hi-Lo trumpets and nylon knuckle cups which will fit front or rear, but you will need the sleeved rods HILO-01 to enable fitment to the rears. For a car set you require 2 HILO k...

Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...

Minispares dry suspension type bump stop with 2 threaded retaining bolts which was replaced by a single bolt on MK4 cars from 1976 on. For 1976 on see FAM2764 or FAM2764MS. (nuts not included)

Upgraded, lower EN8 damper pin. 3/8"unf. Sold singly

Especially useful for competion cars or street cars with lowered suspension.

Its quite a good idea to change these if they are corroded to give a better seating for your dampers.<...