(¥21) £21.38 exc vat
(¥26) £25.66 inc vat
Special order
(¥21) £21.38 exc vat
(¥26) £25.66 inc vat
Special orderRecommended usage 1 x 14A6562 to fit one mini.
Non genuine repair panel for below the lights and above the rear valance, fits all models. Right hand side.
Non genuine repair panel for below the lights and above the rear valance, fits all models. Left hand side.
Group 2 fibre glass wheel arches in premium black finish not requiring paint, judged the best on the market available by our customers, they stick out 1.75" including lip, when bodylines (wheel arch and moulding lip) are kept original. Screws are vis...
Upgraded L/H "A" panel for all Minis with internal hinges,1970 on.
A single wall panel has has a tendency to develop rust spots and is probably one of the most common panels replaced on the Mini.
Only available from Mini Spares th...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
Rubber seal for all mini windshields. Uses locking strip 24A1466(chrome) or 37H8052(black.) REMEMBER YOU MUST FIT THE RUBBER TO THE BODY FIRST. DO NOT USE THE STRING METHOD BECAUSE IT STRETCHES AND TEARS THE RUBBER.
There is a later wider r...
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
Genuine Mini Spares product-These are copies of the original solid type, with stronger reinforced internal wire and with the holes for drainage and securing.
These fit either side door where the holes line up on the window catch moulding. C...
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
Set of four very good copies of the original rubber wheel arches as fitted to
the sports pack models from 1997 on. Not quite as good as genuine in finish perfection,BUT THE DOWN SIDE is the coating needs proper etch primer for applying paint...
Draft excluder for sliding window doors as fitted to Mk1/2 Minis. Right hand side. Properly cut angles as original.Either crimp both ends with your fingers to make it stay on door glass or use a glue as per the factory on later vans.
Qty one...
This is the bracket on the inner wing to put your bonnet prop into when the bonnet is in the open position.
This lower rear valance is without any fog lamp or wiring holes and is also available as a genuine panel under part number 14A6940.
Used on all MK1/2/3 bootlids where there are 26 little holes drilled around the inner edge. These are for use with 14A6585 seal--- Later cars 1988 on fitted a seal to the body only (cke10018).
These are the clips that hold on the vertical seam mouldings on all minis.
The original metal type are prone to rust so Mini spares producedd these stainless steel versions which are also cheaper. Supplied as a single clip, order as many as ...
Draft excluder for sliding window doors as fitted to Mk1/2 Minis and vans.
Left hand side..Either crimp both ends with your fingers to make it stay on door glass or use a glue as per the factory on later vans. QTY one per door. Angled cut a...
non genuine boot hinge panel repair piece
this panel is just longer then the 3 central bumper holes and has the boot hinge holes plus the part of the body that the boot hinge seal sits on making this a perfect rust or accident repair panel. ...
The oversill panel includes the horizontal external seam and wraps all the way down with a lip that meets the horizontal part of the floor.
This is the 6 vent style which started on Mk3 minis late 1970 on. Most 1970 including all Cooper S M...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.