(¥12) £12.00 exc vat
(¥14) £14.40 inc vat
In stock
These are the same as were suplied to Rover and fit properly. Beware of inferior copie...
(¥12) £12.00 exc vat
(¥14) £14.40 inc vat
In stockRecommended usage 1 x BG2400 to fit one mini.
4 wheel arch covers in stainless steel. The ultimate in dress-up are these almost chrome looking flares. Designed to fit over the plastic arches (GAW117) as fitted on all stock Minis since 1984. These are the same as were suplied to Rover and fit pro...
Complete fitting kit as supplied with most Tex mirrors.
Genuine Mini Spares product. The seal that goes on the neck of petrol tanks as protection against water intrusion and to also to make the hole look neater, so replace them when they crack or shrink through heat. This is the original fatter type as us...
Aftermarket decal kit for Balmoral models. Kit includes 2 rear quarter decals, 1 bootlid decal and pinstripes.
Roof gutter trim clip in stainless steel, ideal finishing item for our MT632 roof gutter trim.
Clip for Door Handle required when changing barrel set. Heavy duty round spire clip specially made for the job.
Factory fitted rivet for the mini special wheel arches, the plastic type fitted as standard from 1984 to cover 12" wheels.
16 required but beware of the front rivet on the rear wheel arch as it goes through a double skin. 5/32" TYPE 7/16" LO...
The front bumper of your Mini should be mounted to this simple 'L' bracket that should in turn be spot welded to the lower edge of your front panel. Often damaged in accidents with the bumper. If you replace the entire front panel of the Mini it incl...
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
In 1993 the moulding between the wheel arches was changed from black plastic to rubber and was still used on twin point rubber arches. This is the Minispares version which is a slightly more rounded profile.
New Stainless steel door mounted mirror, complete with fixings for all 1980 onwards Mini's. This ensures they are a direct swap for the standard black plastic and painted door mirror's. These stainless mirror's are mounted on a very high quality chro...
Pair of Genuine Mini Spares original type black plastic mirrors fitted as standard from 1980 and have been supplied by us since 2015 when Rover ceased production.
These mirrors are denoted by being supplied with a slightly different shape b...
Windshield washer fluid original D shape bottle known as 1 pint or 1/2 litre size bottle, for those after originality. This was replaced by the larger bottle to help comply with MOT standards where people complained the bottle was too small to hold ...
These Mirrors are made in the UK by Tex. Slightly convex lens gives excellent rearward visibility. Left side. Right is GAM217. For fitment to laters cars originally fitted with plastic mirrors, use fitting kit M90997. See also
G...
Genuine Mini Spares product as originally made by Pianoforte and then Mini Spares for Rover.Clips for this are EYC10048
This is the 1/2" tall thinner type fited to wind up window cars from 1970 on.
The original 1" talle...
An aftermarket version of the mini bumper in stainless steel it has the original type open ends (Rover curled the sharp edges over) - BUMPER BOLTS ARE FITTED BUT NO NUTS -3 required metric M6 thread nuts FS106047
For top qualit...
Aftermarket wings do the job at a fraction of the cost of originals. This right front wing for the Mini will fit all MKI, II, III, IV. A slight difference exists between the early and the later models as to headlamp mounting holes. These reproduction...
Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.
Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.