SCREEN MK1 REAR HEATED CLEAR GLASS
14A7056HEATED

($237.00) £237.00 exc vat

($284.40) £284.40 inc vat

In stockIn stock
Mk1 rear heated screen.

($237.00) £237.00 exc vat

($284.40) £284.40 inc vat

In stockIn stock

Recommended usage 1 x 14A7056HEATED to fit one mini.
Windscreens - Qty 1

People also bought products

Never have a misted up front screen again. Not as quick working as the Monte Carlo type but the heating element wires are not so conspicuous. Not suitable for twin point cars as the have the mirror locating area is built into the screen but will acua...

Never have a misted up front screen again. As used on Monte Carlo and other top Rally cars. 2 horizontal silver bands/element wires going across the screen a few inches from the top and 3.5 inches from bottom. Not suitable for twin point cars as the ...

Clear laminated windscreen for all minis except Twin point injection cars 1996

on which had a special screen with built in interior mirror base.

IF A MAIL ORDER OR INTERNET ORDER IS PLACED FOR THIS ITEM IT IS AT YOUR (THE CUSTOMERS)...

Front door sliding type front window glass. MK1/2 plus all mini commercial type derivatives

Rear screen seal for mk1 cars which had the smaller rear window 1959-1967.

Front and rear screen with chrome plastic insert.Saving nearly 15% on cost of individual partts

Genuine Mini Spares mouldings product as supplied to Rover.

These are the later door mouldings that prevent water running down the windows into the door causing rust and have the black platic ends fitted for later car safety regulations but ...

Sliding window type weatherstrip kit R/H

kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with ...

Sliding window Mini models all must now use these black plastic locks for the windows. Our special kit includes a complete set of all the pieces: 4 latches, rubber seals, screws and chrome nuts.This kit is a great saving over buying all the parts ind...

Finishing clip in brightwork (chrome colour)for 24A1466MS locking strip in windscreen and backlight rubbers.

The MK1/MK2 Mini not only has a smaller rear side quarter window than the MK3 but also the rubber seal is cosmetically different. The only seal available for years was the MK3 which has a grain texture on the inside edge. Now in stock are very good r...

Draft excluder for sliding window doors as fitted to Mk1/2 Minis. Right hand side. Properly cut angles as original.Either crimp both ends with your fingers to make it stay on door glass or use a glue as per the factory on later vans.

Qty one...

Front door sliding type window rear square glass, as fitted to MK1/2 saloons plus all vans and pick-ups

Sliding window type weatherstrip kit L/H.

Kit contains lower and upper sliding channels plus the vertical strip that attaches to the glass as a draught excluder plus the stainless steel window catch runner that the lower channel sits in,with...

The plastic chrome insert for fitting in the windscreen and backlight rubbers of all minis. You will require TOOL02 to fit these.

Draft excluder for sliding window doors as fitted to Mk1/2 Minis and vans.

Left hand side..Either crimp both ends with your fingers to make it stay on door glass or use a glue as per the factory on later vans. QTY one per door. Angled cut a...

The chrome moulding to fit the door bin on first 80 thousand MK1 minis with extra length tag with screw hole for location.

This is held on by screws but a single sided prong clips ADH3809 can be used in the centre - beware other...

Front subframe fitting kit for pre 76 twin bolt subframes, locktabs are included but not the subframe tower spacers as these rarely need changing.

Early Mini runner for metal type window catches pre May 1963 with sliding windows on the L/H front doors, these are the runners that hold the channel and have holes to lock the window catches. Now made in stainless steel by Minispares to ease rust pr...