($1.00) £1.00 exc vat
($1.20) £1.20 inc vat
In stock
($1.00) £1.00 exc vat
($1.20) £1.20 inc vat
In stockRecommended usage 2 x BYF10001 to fit one mini.
This screw is used to hold together the 2 halves of the disc shields on all
mini front discs. Also used to retain the boot lid cable to the bootlid.
Used on various door handles and door remote link.
This 3/16"unf screw was...
These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car
37H3043 can be u...
Require cleaning weekly. Up until December 2003 we would have been embarrased to sell the only chrome boot hinges then available. They were very bad fitting, looked poor quality and had so much play in them they were totally useless. But along came a...
This screw is used to hold together the 2 halves of the disc shields on all
mini front discs. Also used to retain the boot lid cable to the bootlid.
Used on various door handles and door remote link.
This 3/16"unf screw was...
These screws fit the lower 2 holes on all boot hinges.Also see 24A2175/6 gaskets
that you will need. 1/4" unf 5/8"long, also for tailgate stays on pickup.
Key barrel set for Mk3 onwards door handles and boot handles.
This kit contains all the floor brackets and mounts required for fitting Minis with 7.5 gallon tank 10/12" wheels or with 165 profile tyres.
The boot board bracket 14A9783 is not included
For 10" wheels with 145 tyres ...
Threaded boss that fits in the floor of MK1 minis for the spare wheel clamp 14A6511 to screw into.
Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)
A complete set of 2 front door and one boot handle in chrome all with the same key numbers for wind up window door minis 1970on (keys included).
Door Handle Gasket's should also be replaced at same time, CZH1729 and [link]ALA579...
This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.
These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.
These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.
Mk III Chrome boot handle as fitted to all saloons from 1970 on. Includes 2 keys and paper gaskets.
Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...
If you want your door and bootlid to have new or matching keys this is the easy way. The standard set includes two barrels with matching keys. This is only suitable when you require a drivers door and boot handle to match on MK1/2 cars only. This fit...
Do not forget to replace this little rubber seal that stops water getting into the boot lid via the handle hole. For sliding window type cars the door locks use ADA3817.
On mk3 models the small door gasket on the Mk3 wind up window door hand...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.