($238.50) £238.50 exc vat
($286.20) £286.20 inc vat
In stock
Supplied unpainted ready for door skin fitment.
($238.50) £238.50 exc vat
($286.20) £286.20 inc vat
In stockRecommended usage 1 x MSP021 to fit one mini.
Countersunk, crosshead screw. 1/4"unf 19mm (3/4") total length.
This screw fits the internal door hinges on wind up window cars and the striker plate on the B post.
These shims are what the factory used to fit on the other side of the hinge panel as a stiffener and sometimes even to align the doors themselves, 2.2mm thick.
This is a Non genuine L/H outer MK3 door skin.
It does not fit as well as the genuine CZH3301 but a good inexpensive replacement less mirror holes.
Special thread cutting screw 1/4 UNF 1.25" (31mm) long.
Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...
This is a Non genuine L/H outer MK3 door skin in lightweight Aluminium
It does not fit as well as the genuine CZH3301 but a good inexpensive replacement less mirror holes. Nearly 3kg lighter than the standard doorskin.
Genuine L/H door without crash bar which only later cars had fitted. This door also has no hinges.This door also has no hinges. L/H door framework is available as MSP021.The later type door with the crash safety bar fitted internally are...
Mk3 Mini onwards door frame assembly without the door skin R/H.
Supplied unpainted ready for door skin fitment.
Reinforced elastomer liner for door trim made from VELVEX to prolong the life of your door cards.Die cut on press tools that make the original door cards. Each hole for door locks, window winders, door handles, speaker holes are precision cut to fit ...
Non genuine R/H repair section
for wind up window type doors this is the lower 2-3" of the inner skin and the bottom of the door section that usually rusts out-includes a lip section where the outer skin flaps overlaps for fitment--new panel...
Non genuine L/H repair section
for wind up window type doors this is the lower 2-3" of the inner skin and the bottom of the door section that usually rusts out-includes a lip section where the outer skin flaps overlaps for fitment--new panel...
non genuine R/H outer MK3 door skin.
not as good a fit or looking as the genuine CZH3301 but a good inexpensive replacement less mirror holes
This is a Non genuine L/H outer MK3 door skin.
It does not fit as well as the genuine CZH3301 but a good inexpensive replacement less mirror holes.
MK3 Door & boot handle fitting kit, including original type screws, star washers and gaskets.
MK3 door hinge fitting kit for all internal hinged doors. (hinges not included)
Special thread cutting screw 1/4 UNF 1.25" (31mm) long.
Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...
4 Non Genuine door hinges as a car set for wind up window type doors from 1970 on. These are a top quality item as opposed to the cheaper junk version available on the market.
Sold seperately as
top right CZH202MS 1 r...
Sponge type seal on L/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust.
Sponge type seal on R/H A post of all minis with wind up window type doors to protect from water running down into body. A part you must keep your eye on to stop rust, if the sponge is gettig hard then replace it.
Holds the window regulator to the door on wind up window minis from 1970 on.
Also holds fog lamp bracket to rear valance. 1/4" unf with 1/2" thread on
panhead type screw.
For wind up window type doors this is the mini saloon and clubman estate r/h
door lock mechanism mounted on the door.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.