£82.50 exc vat
£99.00 inc vat
In stock
Super accurate and a 100% level floor is not required.The geometry angles are measured by a special scale and plumb line on the base board and supplied with easy to use instructions.Should be used in conjunction with TOOL11 wheel tracking tool
£82.50 exc vat
£99.00 inc vat
In stockRecommended usage 1 x TOOL10 to fit one mini.
Simple and accurate tool for checking the wheel tracking-this tool is essential when suspension modifications or upgrades are carried out. A completely flat and level floor is not neccessary. Should also be used in conjunction with TOOL10
Radius arm bearing removal, fitting and reaming tool fitted with a pilot to keep the reamer in line with the needle roller bearing. Full instructions supplied.
We all knows Mini's like to leak a little oil... This drip tray is great for protecting your garage floor, low profile and measures 60x40cm.
Perfect for using whilst rebuilding heads, engines and gearboxes to keep all the small pa...
Metric & Imperial offset feeler gauge set, ideal for setting tappet clearnace, primary gear end float etc. Offset for ease of use.
Imperial: .005/.006/.007/.008/.009/.010/.011/.012/.013/.014/.015/.016/.017/.018/.019/.020/...
Imperial & Metric spanner set ideal for completing most tasks on your classic Mini, these are mirror polished spanners.
Contents: Bi Hex x Metric combination spanners 6, 7, 8, 9, 10, 11, 12, 13, 14, 17, 19mm and Stubby 10, 11, 12, ...
3/8" 6 point shallow AF/Imperial Socket set
Sizes 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16"
This tool bolts where the starter motor fits to lock the flywheel in place when trying to remove the flywheel bolt/crank pulley etc.
Red Rubber Grease has been specifically designed for use in environments where compatibility with seals and/or resistance to Hydrocarbons is required. Red Rubber Grease is compatible with both natural rubber and synthetic seals. The formulation of th...
1/2" hex key socket needed when using our upgraded crank pulley bolt C-AHT147, 1/2" drive.
Copper Grease/Anti-Seize high melting point assembly grease supplied in 500g tub, suitable for jobs such as lubricating bolt threads, essential for any restoration project!
CV fitting tool, designed to assist with the correct fitting of CV joints, wheel bearings or drive flanges, as specified in the Haynes workshop manual. The wheel bearing should be torqued to the specified setting using this washer, and then removed a...
A series crankshaft tap in 5/8 x 16 tpi Whitworth form, used for both ends of the crankshaft.
Roll pin punch for removing RPS1416 roll pin from the gear selector mechanism.
Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.
Multi-Purpose LM2 Grease supplied in a 500G tub.
This grease is suitable for Wheel Bearings, Radius Arms, Upper arms, knuckle joint cups and other regular greasing points.
ESPECIALLY FOR MINIS
This 20-50w semi synthetic oil is produced especially for minis where it needs to lubricate both engine and gearbox parts giving the neccessary coating and protection. Semi synthetic has a long life to 100c with maximum ...
This new type suspension cone tool for removing or refitting the rubber suspension cone is METRIC thread only and improved by using a hex(allen)key to screw in and hold the centre spindle. There cannot be many cars left out there with the AF type th...
This tool/gadget allows you to balance both air intakes on either twin SU or twin choke carbs so they flow exactly the same to give better performance and economy.
Spanner for adjusting the jet on silver coloured original jets on HS type carbs
short handle to enable use in tight places such as a mini engine bay.
WILL NOT FIT LATEST BRASS TYPE ADJUSTER NUTS AS FITTED TO REPLACEMENT CARBS SINCE ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.