£13.50 exc vat
£16.20 inc vat
In stock
£13.50 exc vat
£16.20 inc vat
In stockRecommended usage 1 x DEP74500 to fit one mini.
Radius arm bearing removal, fitting and reaming tool fitted with a pilot to keep the reamer in line with the needle roller bearing. Full instructions supplied.
We all knows Mini's like to leak a little oil... This drip tray is great for protecting your garage floor, low profile and measures 60x40cm.
Perfect for using whilst rebuilding heads, engines and gearboxes to keep all the small pa...
Metric & Imperial offset feeler gauge set, ideal for setting tappet clearnace, primary gear end float etc. Offset for ease of use.
Imperial: .005/.006/.007/.008/.009/.010/.011/.012/.013/.014/.015/.016/.017/.018/.019/.020/...
Imperial & Metric spanner set ideal for completing most tasks on your classic Mini, these are mirror polished spanners.
Contents: Bi Hex x Metric combination spanners 6, 7, 8, 9, 10, 11, 12, 13, 14, 17, 19mm and Stubby 10, 11, 12, ...
3/8" 6 point deep AF/Imperial Socket set
Sizes 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16"
3/8" 6 point shallow AF/Imperial Socket set
Sizes 3/8", 7/16", 1/2", 9/16", 5/8", 11/16", 3/4", 13/16"
1/4" 6 point deep AF/Imperial Socket set
Sizes 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2" AF
1/4" 6 point Shallow AF/Imperial Socket set
Sizes 1/4", 9/32", 5/16", 11/32", 3/8", 13/32", 7/16", 15/32", 1/2" AF
This tool bolts where the starter motor fits to lock the flywheel in place when trying to remove the flywheel bolt/crank pulley etc.
1/2" hex key socket needed when using our upgraded crank pulley bolt C-AHT147, 1/2" drive.
Copper Grease/Anti-Seize high melting point assembly grease supplied in 500g tub, suitable for jobs such as lubricating bolt threads, essential for any restoration project!
CV fitting tool, designed to assist with the correct fitting of CV joints, wheel bearings or drive flanges, as specified in the Haynes workshop manual. The wheel bearing should be torqued to the specified setting using this washer, and then removed a...
A series crankshaft tap in 5/8 x 16 tpi Whitworth form, used for both ends of the crankshaft.
Roll pin punch for removing RPS1416 roll pin from the gear selector mechanism.
Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.
Multi-Purpose LM2 Grease supplied in a 500G tub.
This grease is suitable for Wheel Bearings, Radius Arms, Upper arms, knuckle joint cups and other regular greasing points.
Mineral oil especially formulated for the combined engine and gearbox such as the mini, but for better gearchange etc use MILERS002 except on rebuilt engines where pistons must be allowed to bed in using non synthetic oil. 5 litre bottle.
Se...
This new type suspension cone tool for removing or refitting the rubber suspension cone is METRIC thread only and improved by using a hex(allen)key to screw in and hold the centre spindle. There cannot be many cars left out there with the AF type th...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.