PISTON RING SET FOR 21250/1 +40

Rover piston TAM2048 stamped 21962 with ring sizes 1.501mm and oil ring 4mm but some pistons have been stamped 21963.

-Does this get confusing?

So lets clear it up; the easy way to identify the piston and corrrect rings are as follo...

£61.70 exc vat

£74.04 inc vat

PISTON SET 998 FLAT TOP CIRCLIP TYPE +60 OVERSIZE

ADU3490-60

998cc flat top 3 ring circlip type piston set as fitted to early A plus to replace 4 ring set type. Gave 10.3 to1 CR and is a good alternative to use on any 998 with circlip type pistons. Replaced 4 ring(3 ring and scraper) P20754 from Hepolite 1980...

£152.00 exc vat

£182.40 inc vat

PISTON RINGSET 998cc +60 PRESSFIT

R43240-60

£81.60 exc vat

£97.92 inc vat

PISTON SINGLE 1275 LOW DRAG +60 8.8CR

P21251-60

60 thou oversize low drag slipper type pistons for modern day compression ratios and unleaded fuel.

Typically installation will result in a minimum 8.8:1 compression ratio but on some Metro versions it was higher.

Current pistons ...

£48.00 exc vat

£57.60 inc vat

PISTON RING SET FOR 73.5 C-STR311 + OMEGAS

C-STN96

NPR Ring set for 73.5mm Mega and Omega pistons with 1.2mm thick rings and 3 piece oil rings-also for new range of EVO pistons C-STN101

£78.00 exc vat

£93.60 inc vat

CAMSHAFT 1275-1380 A plus

EVOLUTION002

Genuine Mini Spares camshaft for use with 1.5 rockers if preferred--below 5000rpm should produce more power than the 286 profile. Close to MDM274

Cam Timing

107 degrees at full lift on No1 inlet

SEAT...

£82.50 exc vat

£99.00 inc vat

SIMPLEX TENSIONER 6 PIECE KIT

MSSK051

Parts required to stop timing chain rattle on A plus engine with single row chain.Last chance to buy the plate and pin to hold the tensioner as they are

obsolete from Rover.

It is worth the expence to fit MSSK051EVOkit...

£21.06 exc vat

£25.27 inc vat

WASHER FOR BLOCK DRAIN PLUG (53K2853)

6K638

Washer for the drain plug on the rear of the block (53K2853)

£0.53 exc vat

£0.64 inc vat

BOLT FOR CMS10 3.25"LONG 7/16"

CMS10BOLT

The high tensile bolts supplied with the 998 centre main strap kit.

£1.77 exc vat

£2.12 inc vat

TIMING CHAIN TENSIONER. PRE 99H791/10H791

8G549

RUBBER CHAIN TENSIONER (2 PER CAR) FITS WITH WIDE GEAR ONLY.

Sold singly 2 required per engine.

£3.00 exc vat

£3.60 inc vat

BIG END SET 10 OVERSIZE 1275 EXCEPT COOPER S

AEB91306-10

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

£28.50 exc vat

£34.20 inc vat

BIG ENDS SET STANDARD 1275 EXCEPT COOPER S

AEB91306-00

Big end shell bearings for the 1275 larger 1.75" diameter rod pin-not Cooper S

( Tri-Metal )

Sintered copper lead, lead plated,steel backed

Nominal Composition

Copper 74%

Lead 24%

Tin ...

£28.50 exc vat

£34.20 inc vat

DUPLEX TIMING CHAIN.DOUBLE ROW ENDLESS

2H4905

For race quality chain see 2H4905EVO.

It only makes sense that if you have your engine out of the car that you replace the timing chain. The chain controls the timing of the camshaft and even a slight amount of wear or stretch c...

£5.78 exc vat

£6.94 inc vat

MAINS STANDARD 1275 A PLUS ONLY 3 SIDE TAG 3 CENTR...

AEM91886-00

Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...

£30.00 exc vat

£36.00 inc vat

TAPPET CHEST GASKET (EARLY CORK)PRE 1966

12A1139

All early A series engines had these gaskets made in cork for the rear convex shape tappet chest covers and fitted to minis until 1966. The convex side plate was only designed to take these cork type gaskets and the later concave shape cover will onl...

£1.35 exc vat

£1.62 inc vat

MAINS SET 10 OVERSIZE 1275 A PLUS ONLY 3 SIDE TAG ...

AEM91886-10

Original equipment quality for factory built engines giving longer life expectancy on road cars under variable conditions of oil and use. These are the 1275cc mains as fitted to A Plus engines with the locating tab in the middle rather than to the ou...

£30.00 exc vat

£36.00 inc vat

MAINS SET 20 OVERSIZE PRE A PLUS/EARLY A+ 1275

AEM91120-20

Main bearings, 1275 2" mains.20 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use

Nominal Composition

Copper 74%

Lead 2...

£30.00 exc vat

£36.00 inc vat

PRE A+ 848/998/1098 CORE PLUG

2K8169

Convex type core plug at 41.4mm for all early A series blocks up to A plus.

4 required per engine-these are known as the flat type wher the centre has to be pressed in so the convex plug spreads out. The Cooper S althouh same size was a cup ...

£0.85 exc vat

£1.02 inc vat

OIL PUMP GASKET 4 BOLT TYPE

12G730B

Universal paper oil pump gasket for all A series engines. Fits between pump and block. See GUG705560GM for genuine.

£0.30 exc vat

£0.36 inc vat

TIMING CHAIN TENSIONER PAD from eng.no.99h791/10h7...

12G2621

Plastic tensioner pad to take up the slack in single row timing chains on A plus engines that wears and should be replaced nearly every time you have the timing cover off. From engine numbers 99H791/10H791 AND ALL A+. Fitted to 998/1100cc from 1979 a...

£6.43 exc vat

£7.72 inc vat

MAINS SET 30 OVERSIZE PRE A PLUS/EARLY A+ 1275

AEM91120-30

Main bearings, 1275 2" mains.30 thou oversize. Heavy duty steel backed bearing for durability and long life. The bearings to use if you want it to last. The only bearings to use

Sintered copper lead, lead plated,steel backed

Nomina...

£26.25 exc vat

£31.50 inc vat