£7.50 exc vat
£9.00 inc vat
Out of stock
£7.50 exc vat
£9.00 inc vat
Out of stock
Red Silicon Top Radiator Hose
Unless your're heavily into the concours scene you'll love these hoses! These silcone hoses will withstand higher temps and pressures and will last virtually forever!Made to fit any 850/998/1100cc minis plus HI...
Red Silicon bottom Hose- Unless you're heavily into the concours scene you'll love these hoses! These silicone hoses will withstand higher temps and pressures and will last virtually forever! And if you ever had to replace a lower hose you'll appreci...
Silicone heater hose, 42" for cars with the original heater valve bolted on the cylinder head.
Cars after 1976 require one of this 42" length and one C-GRH1006 39" length.
Cars from late 1984 to 1988 had 5/8" outlets on...
Silicone heater hose, 39" for cars with the original heater valve bolted on the cylinder head.
Pre 1976 cars can use 2 0f these lengths, commonly known as 1/2" bore heater hose. also see C-GRH1007 for the longer 42" hose on 1976...
Made for small bore Mk2 minis except clubman these super flexible hoses are easier to fit than rubber and last so much longer. See C-GRH003 also for all 998 Clubman and original MK1 radiator with longer top hose which measures 7" long (c...
5/8" straight connector piece for heater hose modifications on late minis.
Useful when re-routing hoses or joing hoses.
Long lasting silicon by pass hose between cylinder head and water pump.
These are easy to cut and slide on easier than the old conventional rubber type.
It has been made this length to fit 1275cc engine,which used the longest hose.<...
Made for small bore Mk2 minis except clubman these super flexible hoses are easier to fit than rubber and last so much longer. See C-GRH003 also for all 998 Clubman and original MK1 radiator with longer top hose which measures 7" long (c...
Original mini half inch bore heater hose cut to metre lengths as required.
The MK1/2 had one hose 35" and one at 16" long, MK3 had one 35" and one at 29".(These are all maximum lengths).
Please note MK4 1976 on some had 42" heater t...
Water hose pipe clip for the GRH1140 top hose and twin point injection cars which had larger hoses fitted .This clip will wind down to fit most radiator hoses if required.
Reinforced in kevlar for longevity as standard rubber hoses seem to be poor quality these days. This is not the true strand kevlar hose we use in GRH240KEVLAR bottom hose.This has a longer radiator end than the cooper S and other 1275cc ...
Real Kevlar stranded hose,2 year guarantee-the only true Kevlar threaded hose available where you can see the strands, it is made for longevity and low heat transfer making this the best selling bottom hose in the market.
The built in proper...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...
The upper radiator bracket was different on clubmans and was wider owing to the fact that a spacer was often used on the fanblade for clearance.
Hose clip for 5/8" heater hose and used to locate 3/4" diameter anti roll bar in our C-AJJ4008 kit.
Clear plastic windscreen washer tubing sold by the metre only. This is the larger size and was known as 1/4" bore because GWW201M is 1/8" bore. This hose is actually now known as 4.8mm which is nearer 3/16".
this was known as 1/...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.