£27.00 exc vat
£32.40 inc vat
In stock
In 1974 the Mk2/3 lamp was superseded by a rectangular lamp 13H8919 which was replaced by same shape lamp EAM1650.
The earlier lamp with pointed torpedo ends and a black switch was used on MK1 model Minis,Elf & Hornet MK2,See 14A9148 which was an alternatives to 13H192.
On the Mk3 Mini and Mk2 Elf/Hornet it was fitted on the side of the roof-whereas on MK1/2 with 2 piece headlining it was fitted in middle of roof.
Most have now tarnished and changed colour considerably as well as becoming very brittle and break when removed so buy a new one whilst you can.
The screw size for lamp fitting is 3/4 inch No6 preferably countersunk.
Wingard were taken over in 1972 by Griffiths and Bentley owners of Britax and then rationalised their business after 1973 when they became part of Bristol Street Motors Group. This lamp was discontinued after 1974 and replaced by the oblong lamp 13H8919 and the EAM1650 until 1983.
£27.00 exc vat
£32.40 inc vat
In stockRecommended usage 1 x 13H4398 to fit one mini.
5 watt 12 volt festoon type bulb. For rear number plate light (PRC1230A) & interior lamp.Sold individually
Interior lamp with a black on/off switch and pointed torpedo ends.
Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.
Also there was an alternative lamp with black switch and square ends 13H192 which w...
Interior lamp with a black on/off switch and pointed torpedo ends.
Also fitted many of the 1959on range of Austin A55/60 Cambridge, MG Magnette etc.
Also there was an alternative lamp with black switch and square ends 13H192 which w...
This will replace the orange lens fitted on the wing of all cars from 1986 on, fitted with an orange LED. If you need a new loom for this lamp see AFU3358. Sold singly. Does not require a resistor.
Resistor for AFU3389LED and AFU3389WLED, this is needed to enable the lamps to function properly. Sold in pairs.
Screw for holding PRC1230A to the number plate light body, 1970 onwards.
INDICATOR LAMP WITH WHITE LENS AND LED BULBS. sold singly,2 required per car
Stainless steel screw kit for all mk2/3 lens to lamp body. Comes as a car set with six screws and six fibre washers.
A single plastic headlamp bowl only, to accept the levelling motor and rim for all twin point (1997 onwards) Minis plus some export SPI models.
Auxilary wiring for genuine Rover spot and fog lamps needed when fitting genuine lamps to cars not originally fitted with auxilary lamps or for cars that have had the wiring damaged. This loom is supplied with complete lamps XBN10008 and...
This chrome over brass wing side repsater lamp rim will fit of the square/oblong lamp lens where fitted on the wing. Fits straight over the original lens and retained by bending the tag. Made in brass to prevent rusting, but also to obtain that deep...
New lenses do a lot to improve the looks of a car, and may make it more visible. To make sure that they match we recommend that you replace both lenses together.
For wipac quadoptics-replacement bulb holder for lamps also supplied in kit.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. The halogen headlamps have very bright 55/60 watt bulbs. Their special lens gives g...
The best chrome type available with screw and washer.
A headlight trim ring is only the starting point of a good looking car, but you have to start somewhere. Sold singly 2 required per car. These are the original type chrome over solid bras...
Genuine L/H lamp.Beware of cheaper inferior lamps for sale.
Fitted from 1976 on as standard equipment this was the Lucas style lamp with the built in reverse lamp.Supplied with gaskets. Many people now change the upper lens to the more fash...
Side lamp bulb on all sealed beam unit headlamps.Sold individually
These strange little bulbs are also used on the front wing side indicators fitted from 1986 on. The same bulb in orange or amber equivalent is GLB501A for use wi...
Headlamp bulb found in many of the post sealed beam unit cars. An upgrade is available as GLB472X.Sold individually
Almost any screw will hold the chrome headlamp bezel on, but only one is correct! These screws are stainless steel and will never corrode plus they have the little rubber washer on the backside so that the screw will not fall out when trying to fit ...
These are for Left had drive L/H/D. See S4698B for Right hand drive R/H/D.
Even at normal highway speeds it is common to "outdrive" conventional headlamps. These halogen headlamps have very bright 55/60 watt bulbs. Their special...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.