£2.93 exc vat
£3.52 inc vat
In stock
£2.93 exc vat
£3.52 inc vat
In stockRecommended usage 2 x 2A4267POLY to fit one mini.
The correct screw for holding the 2A4267MS bump stop for the upper arm on the front suspension. 3/16"unf 1/2"long flat head phillips type screw.
Mini Spares Non genuine a re-bound buffer which is the same as Rover Xparts are supplying as genuine. Fitted purely to prevent the top arm crashing in to the subframe on full droop (as when airborne),and stopping the suspension ball joint going bound...
Genuine Mini Spares UK made complete joint with the following specifications,
correct dimensions and shape of pin and ball in EN24T, using correct spec grease,
genuine original shape cup using correct material (21A423MS...
Genuine Mini Spares UK made joints are complete with the following specifications, correct dimensions and shape metal knuckle in EN24T, with the genuine cup made in original material and correct shape (21A423MS) and an upgraded poly boot...
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.
Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...
This is a budget way of improving the stability of the front subframe leaving the rear mountings standard for quietness.
It only includes the 4 poly tower spacers and for the front of the front subframe 2 poly spacers and 2 metal washers.
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...
A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.
From November 2003 they have been made from a s...
To compliment the top alloy blocks (C-STR640), those troublesome front rubber mountings can be replaced by alloy cast mountings which will not break and further enhance roadholding. These are for the front of the front subframe on vehicles built from...
The set of four aluminum top front subframe mountings are to replace the standard rubbers fitted on vehicles from 1976 to present date. These alloy pads help reduce subframe movement, which is detrimental to handling when driven hard. As the original...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
Lower arm bush for pre 1966 cars. The lower arm had a straight hole whereas the later cars from 1966 on had a tapered hole and used 21A1882 bush with a metal sleeve in. This bush has no inner sleeve and it was discontinued in 1966. Sold ...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 can use the same bush (2A5818/POLY) at the front and rear of the subframe, ...
The Mini's rear subframe is rubber mounted. Polyurethane (stiffer, much longer lasting) bushes are now available for the rear subframe trunions. Cars manufactured before 1976 used the same bush 2A5818(C-STR638) at the front and rear of the subframe, ...
Upgraded, lower EN8 damper pin. 3/8"unf. Sold singly
Especially useful for competion cars or street cars with lowered suspension.
Its quite a good idea to change these if they are corroded to give a better seating for your dampers.<...
Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.
Set of 4 bushes.
These metal sleeved bushes are specially...
For Hydrolastic suspension cars, they were made with a 1/4" fixing hole but this needs elongating vertically to get the bump stop to sit properly on the upper arm which had different machine tolerances when manufactured.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.