£2.30 exc vat
£2.76 inc vat
In stock
Other end of the front arm shaft is a larger 7.4mm wide washer which is 2A4326.
£2.30 exc vat
£2.76 inc vat
In stockRecommended usage 2 x 2A7324 to fit one mini.
Thrust washer inner rear on radius arm kit-see picture of kit GSV1125.
The inner is the larger diameter type 36.4mm(1.435")
Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.
Original cone...
Genuine Mini Spares UK made complete joint with the following specifications,
correct dimensions and shape of pin and ball in EN24T, using correct spec grease,
genuine original shape cup using correct material (21A423MS...
Genuine Mini Spares UK made joints are complete with the following specifications, correct dimensions and shape metal knuckle in EN24T, with the genuine cup made in original material and correct shape (21A423MS) and an upgraded poly boot...
Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.
Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...
one piece forged lower rod end arms
unbelievably at this price they are not the welded type as sold by many of our competitors
Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...
Genuine Mini Spares product ideal for road use for maximum performance, where other examples available tail off as they get worked and heat up.
Hilos will be required to enable fitment as they are taller but FAM3968EVO are a str...
Lower suspension arms to give 2.0 extra degrees of negative camber. Stamped with 2.0 Sold in pairs only.
General:See also c-AJJ3360 fully adjustable arms
Negative camber lower arms are specifically forged in different degrees to...
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...
A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.
From November 2003 they have been made from a s...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
Lower arm bush for pre 1966 cars. The lower arm had a straight hole whereas the later cars from 1966 on had a tapered hole and used 21A1882 bush with a metal sleeve in. This bush has no inner sleeve and it was discontinued in 1966. Sold ...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.