£3.00 exc vat
£3.60 inc vat
Out of stock
We have found these clips work fine on standard road use
£3.00 exc vat
£3.60 inc vat
Out of stock
heavy duty circlip on the rear radius arm stub axle to hold it in position
Machined and polished aluminium rear wheel/hub bearing grease cap with cut outs for easy removal.
Metal CV gaitor ties for the outer CV gaitor, slim in design in order to give maximum clearance between CV and hub
Genuine Mini Spares Heavy duty gaiter kit as supplied with our GCV1013 cv joint, contains rubber gaiter grease and metal clips. We consider this the best available with a special shape to stop rubbing or soiling.
Sold singly-2 r...
Non genuine aftermarket only as the genuine originals are obsolete.
These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle; this is ...
This drive flange fits all cars fitted with 8.4" disc brakes except Turbos. Originally intended to use 12" wheels it is an integral part of the front suspension. Sold singly 2 required per car. In addition to providing the connection between the axle...
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the left hand short one.
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the right hand longer one.
There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number GFK3431.
Sold Individually.
In board CV joint(pot joint) gaiter kit with plastic clips and grease.
Non Genuine item many sell as GSV1073.
The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one ver...
Cheaper alternative to genuine timken front bearing kits.
These are very well tried and the best of any of non genuine bearings available.
Sold as one hub kit only. Please note-for arduous or race use Timken bearings in genuine GHK1...
Inboard CV (pot joint) splitting tool used to remove the constant velocity joint from the gearbox by way of driving this wedge-like tool between joint and gearbox. Does not remove joint from driveshaft.
Special grease for Cv joints and any homokinetic joints. Enough for one joint only.
One gaiter, 2 plastic clips and grease. The single largest reason for the failure of this rugged assembly is contamination. Dirt and moisture will destroy one very quickly. The CV rubber boot protects the joint at all angles but if your boot shows an...
Mini Spares own stamped GCV1013. Brand new CV Joints with gaiter, hub nut, grease and clips. Stamped with our part number GCV1013 for identification from may 2014 to denote our authenticity of this top quality joint, sold singly.
These are t...
Front genuine Timken wheel bearing kit for one hub only. Kit comes complete with split pins and inner and outer hub seals.If you suffer from wheel bearing problems check the hub for wear which is usual and use best quality cv joints.
Genuine...
Original genuine sintered split washer for behind the hub nut that goes on the cv joint drive flange.
This is not the cheap old metal type often sold by our competitors which Rover discontinued and changed to sintered for all production car...
This is the small gaiter that sits on the yoke and shaft of all pre pot joint rod change minis. Also fitted on autos and cooper S hardy spicers.
Genuine Rover Xparts item. See BHM7012 which many vendors sell as their GSV1073.
In board CV joint(pot joint)gaiter kit metal clips and grease.
The single largest reason for the failure of this rugged assembly is contam...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.