£18.00 exc vat
£21.60 inc vat
In stock
£18.00 exc vat
£21.60 inc vat
In stockRecommended usage 2 x ATB4098ALLOY to fit one mini.
Fits the rear hub of every Mini to protect the bearings grease from debris, but
this metal cap always seems to get damaged on 10" wheel cars or when you change the bearings - make sure yours are in place.
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Original 17H8597 became NLA from Rover december 2003 as a spare part but this circlip was used to build up the last Rover hub assemblies previous to then.
We have found these clips work fine on standard road use
Metal CV gaitor ties for the outer CV gaitor, slim in design in order to give maximum clearance between CV and hub
Evolution RACE quality universal joint for hardy spicers If you want to prevent disaster, you should check your driveshaft joints before they self destruct! The best and easy way to do that is to listen and feel the car as you lift off the throttle w...
Molybdenum Grease supplied in a 500g tub, suitable for the lubrication of CV joints and any other homokinetic joints.
Genuine Mini Spares Heavy duty gaiter kit as supplied with our GCV1013 cv joint, contains rubber gaiter grease and metal clips. We consider this the best available with a special shape to stop rubbing or soiling.
Sold singly-2 r...
Non genuine aftermarket only as the genuine originals are obsolete.
These are the best on the market where clip grooves are in the correct place to save the driveshaft seizing on. Later model Minis have CVs on both ends of the axle; this is ...
This drive flange fits all cars fitted with 8.4" disc brakes except Turbos. Originally intended to use 12" wheels it is an integral part of the front suspension. Sold singly 2 required per car. In addition to providing the connection between the axle...
As fitted to MPI from 1996 on with an extra O ring. The O ring goes between the first bearing and backplate on stub axle. Rear tapered roller wheel bearing kit, for one wheel.
All post 1985 cars and the Mini Cooper S were equipped with very...
Output drive shaft from the differential on Rod change type gearboxes,the teeth very rarely wear badly but the side cover bushes(2A3538)sometimes ruin the shaft causing those dreaded oil leaks from the seals in the output covers CHM85.
these...
Special height locking type nut for the hardy spicer joints on Cooper S and automatics to fit the 22A1139 bolt. Sorry about the price but only available from Philidas Ltd.
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the left hand short one.
These shafts have changed diameter thickness over the years but these are the
original thick type and upgraded to EN24 for competition or standard uses.
this is the right hand longer one.
Heavy duty needle roller type coupling with plastic ends. The very early Minis used the rubber joint drive couplings GCD101 to eliminate harshness from being transmitted to the passenger compartment. Over the years the rubber will separa...
There are 4 of these to each output flange to which the Hardy Spicer joint bolts. The special philidas nuts for these are our number GFK3431.
Sold Individually.
In board CV joint(pot joint) gaiter kit with plastic clips and grease.
Non Genuine item many sell as GSV1073.
The single largest reason for the failure of this rugged assembly is contamination, dirt and moisture will destroy one ver...
This is Minispares version of the Metro vented disc type drive flange, made without the original Metro wheel centralising lugs.
The wheel centralising lugs as originally used on the Metro have been removed to allow the fitment of all types o...
Only fitted to vehicles with hardy spicer output shafts (Cooper S and autos). Two collets are fitted in the output shaft in the gearbox and located behind the rubber seal 22A1566
Special Tuning hit upon this idea to stop the driveshafts breaking on their rally cars. Do away with the large circlip groove where it broke and weld a spacer on the shaft to locate the CV joint in position. The works department also reduced the stee...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.