BOOT HINGE FITTING KIT
8B12602FK

£3.69 exc vat

£4.43 inc vat

In stockIn stock
Boot hinge gaskets and fittings for original type hinges

£3.69 exc vat

£4.43 inc vat

In stockIn stock

Recommended usage x 8B12602FK to fit one mini.

Kit contained products

These screws fit the lower 2 holes on all boot hinges.Also see 24A2175/6 gaskets

that you will need. 1/4" unf 5/8"long, also for tailgate stays on pickup.

These gaskets should be changed when replacing the hinges-this one goes between the bootlid hinge on the bootlid. See also 24A2176 for gasket on body.

These gaskets should be changed when replacing the hinges, this one goes between the bootlid hinge on the body, see 24A2175 also for upper on bootlid.

People also bought products

This is the boot seal that actually fits on the car body which saved drilling holes in the bootlid. Fitted from about 1988 on.

Bootlid seal for Mini <91. Held in place on the boot lid using 26 clips(part# 14A6585).When fitting, the lip part of the seal open end for clips should face the inner boot catch- (the open end of the seal facing inwards to the bootlid al...

The MKI & MKII number plate panels 14A6468 are hinged at the top to swing out clear of the bumper when you open the boot lid. They were unavailable for years but now they're back. These & 14A6467 are the hinges.

The MKI & MKII number plate panels 14A6468 are hinged at the top to swing out clear of the bumper when you open the boot lid. They were unavailable for years but now they're back. If you also need the hinges they are 14A6466...

Do not forget to replace this little rubber seal that stops water getting into the boot lid via the handle hole. For sliding window type cars the door locks use ADA3817.

On mk3 models the small door gasket on the Mk3 wind up window door hand...

These two simple cables are all that keep the boot lid from crashing down, damaging hinges, bumper and paint. When one fails we recommend replacing both to be sure of the same length. sold singly 2 required per car



37H3043 can be u...

The MKI & MKII number plate panels 14A6468 are hinged at the top to swing out clear of the bumper when you open the boot lid. They were unavailable for years but now they're back. These & 14A6466 are the hinges.

All Mk1/2 had a hinged number plate on the bootlid and these are the buffers that protect your paintwork and help locate the number plate at the correct angle. 2 required per car, sold individually.

Owing to their position on the car and chrome on metal these must be cleaned weekly. They are a direct replacement for MK3 on original number plate lamps and are less the 2 light lens, which are the same fitting for this lamp. These lamps use M4 scre...

All mk3 cars had the number plate on the boot lid and this is the rubber seal to go between the lamp and bootlid.

Up until December 2003 we would have been embarrased to sell the only chrome

boot hinges available. They were bad fitting, looked poor quality and had so much play in them they were totally useless. But along came a set which does fit and is...

Rubber blanking plug 5/8"wide to fit boot floor hole 5/16".

Special shape and strength 1" rubber floor plug. Also speedo cable unused hole where shells have holes for LHD and RHD.

Wiper mounting kit for Mk1 Mini's (3 required per car). Each kit comes with a pin, nut, 2 washers and mounting rubber.

Special thread cutting screw 1/4 UNF 1.25" (31mm) long.

Screw to hold the lock assembly on the door of MK3 cars with internal hinges and wind up windows. On new doors or for easy fitment use these special screws with cutting thread (3 sided ...

Used on all MK1/2/3 bootlids there are 26 little holes drilled around the inner edge to hold the seal on and this kit contains the 26 clips. For single clips see 14A6585. Later cars 1988 on fitted a seal to the body only. (CKE10018)

The oil pressure relief valve consists of an aluminum plunger with a heavy spring behind it. Access is through the 15/16" domed cap nut beside the dizzy. Once this nut is removed the spring will be visible. The plunger is beneath the spring and will ...

Original metric fixing nut for genuine Rover sportspack arches.