£0.67 exc vat
£0.80 inc vat
Out of stock
this was repalaced on A Plus engines By ADU4905 seal with a spring seal which is interchangable. See also LJQ101160 the latest Dupont Viton seal which stops smokey engines
£0.67 exc vat
£0.80 inc vat
Out of stock
As an engine wears, the clearance between the valve stem and guide increases; as this gets beyond tolerances the car will tend to smoke under deceleration (when you take your foot off the throttle). Good valve stem seals will allow for greater wear b...
Genuine Mini Spares valve stem oil seal manufactured with original Dupont Viton, as fitted to the twin points engines, are the best material and seal you can use and although expensive are the best to date in stopping the engine smoking.
Man...
Sold individually.
To help rocker pad to valve stem alignment and reduce friction, the standard springs can be replaced with solid spacers and correctb shim set. The spacers and shim kit are sold as C-AEG392.
Genuine version of the thermostat gasket for all A series. Black one side and red the other they are fitted black side to the head. Green to the thermostat.
We have no evidence as yet that they last longer but do look good.
See [lin...
Mini cork Rocker cover gasket, suitable for all Minis and A series engines except those with 11 stud heads (see part number GUG5038VC). A must have replacement item when adjusting rocker clearances. see GUGG705009EVO for sil...
Payen,stamped BK450, original standard composite reinforced gasket used on all large bore engines by Rover including Metro and MG Turbo and is an exceptionally good gasket.
Asbestos free with copper type sealing rings. Compressed volume is ...
Originally marketed by Minispares in the mid 70s so many companies copied them because of their smart looks and ease of fitment. These have been improved by offsetting the arms to help tighten plus stop the arm falling out when they were straight. Ki...
Genuine Mini Spares Performance Copper/steel head gasket.
Based on the original AF460 pre 2000 design plus the old Payen Special tuning C-AHT188 with superior sealing rings.
With modern day technology and NON asbestos l...
Special thin type clip for fitting the water by pass hose between the water pump and the cylinder head. Most ordinary jubilee clips will not fit the tight area where the hose fits. Also used on C-AHH8537 oil cooler hose.
Payen stamped AF470, Standard composite reinforced gasket used on all large bore engines by Rover is an exceptionally good gasket. Asbestos free with special black sealing ring for the oil feed. Compressed volume is 4cc. This MINI head gasket has in ...
New colour, PB104 bronze guides.Although Silicon bronze valve guides were used for their extremely good wear values, they were very hard and not user friendly when fitting. These valve guides are recommended when using all EN21 4N stainless steel val...
Genuine Mini Spares product as everything else on the market was poor fitting and unstable.
For Performance see 88G459EVO made in the USA by a Specialised Racing product company.
All the earlier heads used the 2A11 cott...
Actually 29.3mm (1.15") these valves are in EN214N steel with chrome plated stems for use in standard iron guides. Easily noticeable by their strange design shape they claim to give better flow characteristics.
chrome on en214N steel enables fitment of this valve to standard iron guides.
the flow characteristics of this valve are claimed to give better power when used on standard applications. 35.7mm)1.405") for 12G940 large bore casti...
Collet for the 3 groove valve. Sold per half and 2 required per valve.
These cotters go with AHU1897 top cap. On Turbo heads after engine number 102641 were fitted on the inlet only.
All early 850/997/998/1098cc heads u...
If you drive A-Series cars long enough you will eventually have to replace the water pump bypass hose. These are the best quality available to fit without removing the cylinder head but these fluted rubber hoses have a bad reputation so if possible ...
Original type steel 'S' competition top caps for dual springs.
If you are upgrading from single springs or just want to replace those old worn top caps, these better grade material are the best answer. Eight required per head.
Standard alloy thermostat housing. If you want the larger bore type as used on the Cooper with a sandwich plate see PEQ10019 housing GRH1140.
Requires thermostat gasket GTG101MS or GUG705558G...
Made of thicker, more pliant material with larger ports than the original gaskets. A must for use on ported heads.
Forget all the universal shape gaskets available - this is the original correct shape made out of thick gasket paper.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.