£23.19 exc vat
£27.83 inc vat
In stock
£23.19 exc vat
£27.83 inc vat
In stockRecommended usage 1 x C-AJJ4025COMP to fit one mini.
Steel braided clutch hose for verto type clutches with short lever arm.
Flat top clutch master cylinder to suit PRE 65 minis.
Originally the top of this master cylinder would have had either a removable union or a small hexagonal nut shape machined into it, but neither of these options are available so the pipe ...
Pre verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.
Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.
Only tighten up to 16lbs per sq foot torque when using shake proof wa...
Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...
Braided one piece clutch hose from master cylinder to slave cylinder for left hand drive cars. Suitable for verto and pre verto clutch set ups, 91cm long.
3 piece Verto Clutch kit for Turbo with 180mm plate which can be used on any Verto flywheel including injected cars. Approximately 20% upgrade over standard this is ideal for any tuning mods to any Verto flywheel but cars from 1990 were fitted with a...
Upgraded pre verto clutch lever arm plunger. Surely to be copied by competitors as the early diaphragm clutch really needed a quality item to be remade. This is the carrier that holds the clutch release bearing and on the other end has a hole for the...
Performance type Verto 190mm wide paddle type drive plate as used for racing.
This will not fit pre Verto backplate/flywheel as it is to wide.
Mini Spares Performance clutch plate.
Great upgrade for increased performance engines,tested to 10,000rpm and to destruction for evaluation.
For diaphragm type clutch, pre verto. Great clutch plate and a better priced alternative t...
Performance clutch plate for road and rally Verto type - see also 20% upgraded pressure plate
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
For pre injection Verto clutch cars with pre engaged starter, it is also designed to increase clamping
pressure which effectively upgrades the actual performance of the verto clutch, which with the AP pressure GCC679 (part of G...
Suitable for standard 8.4" / 7.5" /7" brake calipers. Also used for front wheel cylinders on twin leading shoe type drum brake cars. This is where you have 2 cylinders per hub as opposed to the early single leading type which had one cylinder only pe...
This original metal canister master cylinder for Mini with Lockheed embossed on the can part has been available from us since August 2003 and are manufactured to OEM specification part number. Fitted with a plastic cap a metal original alternative is...
Rebuild kit (rubber) for early clutch slave cylinder GSY110 pre verto type. Early Spridgets are identified by a hard line runnung all the way to the slave cylinder. Later 1275's have a rubber hose to the slave cylinder.
one seal...
This new type plastic bodied clutch master cylinder is a replacement for almost every Mini ever made. While the part numbers have changed over the years, the shape, size and function has been the same. THESE NEW PLASTIC MASTER CYLINDERS WILL WORK IN ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.