£93.00 exc vat
£111.60 inc vat
In stock
see C-STR1675 for performance increase. Closed length from pin centres is 215mm-
£93.00 exc vat
£111.60 inc vat
In stockRecommended usage 2 x C-STR1717 to fit one mini.
Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.
Original cone...
Genuine Mini Spares UK made complete joint with the following specifications,
correct dimensions and shape of pin and ball in EN24T, using correct spec grease,
genuine original shape cup using correct material (21A423MS...
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
Genuine Mini Spares product ideal for road use for maximum performance, where other examples available tail off as they get worked and heat up.
Hilos will be required to enable fitment as they are taller but FAM3968EVO are a str...
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...
A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.
From November 2003 they have been made from a s...
Koni Shocks Possibly the best name in shock absorbers, and they're available for the Mini! 20% uprated over Rover standard spec shocks and rebuildable. the adjustment is for fluid degradation rather than performance increase, Adjusting damp...
These cone springs will require Hilo adjustable suspension as they sit higher than the originals.Containg an anti fade property and shape which helps them going off during racing and giving hopefully a season of racing before replacement. A softer ro...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
Mini Spares own to original drawing specifications with heat treatment correctly applied where appropiate.Lack of proper maintenance (grease) will make the pivot shaft and/or bearings wear that much faster. In severe cases the shaft may rust to the b...
Upgraded, lower EN8 damper pin. 3/8"unf. Sold singly
Especially useful for competion cars or street cars with lowered suspension.
Its quite a good idea to change these if they are corroded to give a better seating for your dampers.<...
The front tie rod on the Mini controls the fore and aft location of the lower front suspension arm of the car. In addition it provides a great degree of stability under braking. If your rod is bent or the bushes are worn then you need help. The Tie r...
Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.
Set of 4 bushes.
These metal sleeved bushes are specially...
See-Mini Spares own UK made GSV1118EVO first for a correct upgraded version with an improved poly gaiter and original genuine cup on EN24T pin with correct shape ball for a great value item.
Mini Spares own part will out surviv...
Sold in pairs only.
These arms will give an extra 1.5 degrees extra negative camber over what the standard arms give on your car. To correct all variations of incorrect geometry found on the mini we have produced a pair of on car adjustable ...
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.