£45.00 exc vat
£54.00 inc vat
In stock
These arms will give an extra 1.5 degrees extra negative camber over what the standard arms give on your car. To correct all variations of incorrect geometry found on the mini we have produced a pair of on car adjustable lower arms C-AJJ3360 which replace this original method of gaining negative camber,or C-AJJ3360A for adjustable spherical joint lower arms. Also see 21A1091 for adjustable tie bar rods , and C-AJJ3365 for spherical joint adjustable tie bar rods.ST Abingdon always advised fitting a 3mm plate under the top arm where the bump stop 2A4267 hits
£45.00 exc vat
£54.00 inc vat
In stockRecommended usage 1 x C-AJJ3364 to fit one mini.
Original Bolt with a special length shank for the front suspension tie bar to the lower arm. Always check this out for any signs of wear and replace accordingly.
Only wrong length parts were available in the market so these are the correct l...
Pair of adjustable tie rods. See 21A1092 tie bar kit.
When you change the length of the lower control arm to attain the desired degree of camber, the caster also changes. To reset it you must be able to change the length of the ...
Longer track rod end for running with negative camber, gives an extra 5mm of adjustment approximately over the standard item. Has consistent thread pattern and perfect design to our requirements to fits all known racks and classed as a competition tr...
Mini Spares product UK made especially for use when geometry has been changed, such as fitting adjustable tie rods or lower arms, or on any cars with corrected castor angles.
Set of 4 bushes.
These metal sleeved bushes are specially...
A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.
From November 2003 they have been made from a s...
Ultimate lower arm for road or race. (pair supplied)
One piece, forged, fully adjustable on the car lower arms (with knuckle for bushes) to allow adjustment for any camber setting required. Sold in pairs only. It is recommended that you fit ...
Lower suspension arms to give 2.0 extra degrees of negative camber. Stamped with 2.0 Sold in pairs only.
General:See also c-AJJ3360 fully adjustable arms
Negative camber lower arms are specifically forged in different degrees to...
Genuine Mini Spares standard performance cone utilizing 20 years of elastomer/rubber technology from our competition cones manufacturer. Only beeen available since 02/09/2020 and proudly made in the UK with 10,000 sold by 2023.
Original cone...
Genuine Mini Spares UK made complete joint with the following specifications,
correct dimensions and shape of pin and ball in EN24T, using correct spec grease,
genuine original shape cup using correct material (21A423MS...
Genuine Mini Spares UK made joints are complete with the following specifications, correct dimensions and shape metal knuckle in EN24T, with the genuine cup made in original material and correct shape (21A423MS) and an upgraded poly boot...
Replacement ball joint shims, comprising of 2x 003"(.076MM) shims, 2x 005"(.127MM) and 2 x 010"(.254MM).
Tie rod extra hard rubber bush, harder than standard.
You dont want these bushes too hard as it can cause the threaded on the end of the tie rod to break under extreme conditions.
In theory the outer ones should be harder for rigidi...
Mini Spares quality suspension kit includes all four adjustable alloy trumpets and knuckle joints plus the two extended rod struts required for the rear. Many people will advise you, why you should consider upgrading to the genuine classic "Hi/Lo" su...
Car set of 4 top Subframe tower mountings for Road cars from 1976-2000.
Aluminum pad for the top of each subframe mounting and a poly pad below to replace the standard rubbers originally fitted. The alloy pads help reduce subframe movement, ...
one piece forged lower rod end arms
unbelievably at this price they are not the welded type as sold by many of our competitors
Same as the C-AJJ3360 lower arm kit, but includes the spherical rod ends,spacers and dustcov...
The New Front Evolution AGX shock absorber is twin tube type and gas filled. On car 8 point easy adjustable specific settings. This is currently one of the shortest fitted length dampers we stock. Closed length 210mm from pin centres. Open length is ...
Genuine Mini Spares product ideal for road use for maximum performance, where other examples available tail off as they get worked and heat up.
Hilos will be required to enable fitment as they are taller but FAM3968EVO are a str...
Lower suspension arms to give 2.0 extra degrees of negative camber. Stamped with 2.0 Sold in pairs only.
General:See also c-AJJ3360 fully adjustable arms
Negative camber lower arms are specifically forged in different degrees to...
Angled grease nipple for the upper arm on the front suspension of all Minis
importantly lubricates the upper arm spindle which so often gets neglected so check yours out and make sure this nipple is working properly. Also fits rear radius ar...
Lower arm top hat bush in poly to fit all lower arms with twin taper as standard from 1965. Mini Spares have upped the game once again with these superbly finished bushes which surpass anything on the market. Fitted with a metal bush insert these are...
A must-when the castor and camber angles are changed or whenever the geometry of the car is set up you will require these bushes. They are good for cars with up to 3.5 degrees of castor angle.
From November 2003 they have been made from a s...
Koni Shocks Possibly the best name in shock absorbers, and they're available for the Mini! 20% uprated over Rover standard spec shocks and rebuildable. the adjustment is for fluid degradation rather than performance increase, Adjusting damp...
These cone springs will require Hilo adjustable suspension as they sit higher than the originals.Containg an anti fade property and shape which helps them going off during racing and giving hopefully a season of racing before replacement. A softer ro...
Uses 2 Soft standard rubbers on the insides and the 2 Mauve poly on the outside.
HARD OUTERS / SOFT INNERS - STOPS BRAKE WEAVING.
Don't be confused as this special shore hardness set up was proven after 2 years of testing and is per...
Lower arm bush for pre 1966 cars. The lower arm had a straight hole whereas the later cars from 1966 on had a tapered hole and used 21A1882 bush with a metal sleeve in. This bush has no inner sleeve and it was discontinued in 1966. Sold ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.