MASTER CYLINDER BASE PLATE - '89 ON
CRC8664

£9.57 exc vat

£11.48 inc vat

In stockIn stock
Master cylinder base plate for cars with servo built into the brake master cylinder from 1989 on.

£9.57 exc vat

£11.48 inc vat

In stockIn stock

Recommended usage 1 x CRC8664 to fit one mini.
Brake/Clutch Pedals and Controls - Qty 1

Recommended products

This gasket sits under the clutch master cylinder.

For brake master cylinders see 31G840.

Gasket used under the dual master cylinder brake master cylinder. For the earlier single line brake pipe system see 31G279.

The gasket that sits under the plate which the brake and clutch master cylinders sit on and under the blanking plate on the opersit side. fits all cars

People also bought products

Set of 4 hoses, 2 front and 2 rear.

Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...

Set of 6 hoses, 4 front and 2 rear to fit the ERA turbo.

Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided st...

NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.

These pipes are retail...

We now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.

Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve. fits in the bottom union and goes to left hand union in valve (to go to rear brakes)

Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve

As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.

Single line L/H/D - dry suspension - no servo fitted. If you have drum brakes and a servo you should use GL4992 plus 2 of HF10.

These kits or pipes are approx 35% off retail.

You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good idea to check your metal brake lines; rust on them could be disasterous.This complete kit is available, in non-corroding...

One male and one female end on a copper easy bend brake pipe 106" long

Brake pipe connecting piece originally used on diagonal split system.1.25" long

Single line L/H/D with servo-dry suspension. If you have a drum brake mini then this kit will require 2 front wheel cylinder to wheel cylinder pipes HF10

Adjustable original brake proportioning/balancing valve for racers only.

The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...

Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...

Front to rear brake line kit for cars from 1988-2000 with the factory Servo incorporated into the brake master cylinder. You'd think that the way Minis leak oil they'd never rust on the underside, but they do! If your Mini is rusty below it is a good...

From 1989 minis which have the brake servo built into the master cylinder and it is very difficult to work in the engine bay, especialy clutch changes because of the extra room taken up by this dual cylinder. By replacing the 2 metal brake pipes from...

UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.

Male metric brake union as used on front to rear PDWA valve and later master cylinders. Pipes should be double flared.

Easy bend long life copper brake pipe with 2 male ends and ideal and best replacement for the original 16" pipe from the 3 way union to the brake switch on single line dry suspension minis. These kits or pipes are at least 35% off retail.

Easy bend copper 24"long brake pipe with one female and one male end for the regulator on the rear subframe to the n/s/r hose on hydrolastic cars only.

Also used on split front to rear system with valve in engine compartment - from 3 way uni...