£136.00 exc vat
£163.20 inc vat
Out of stock
Now with Mini Spares easy change front floating bush held in by circlip from March 2016 to save any future costs. Bush used is C-AEA3239.
Bush running ...
£136.00 exc vat
£163.20 inc vat
Out of stock
Genuine Mini Spares product. Spacer fits up against the primary gear on the crankshaft and held on by the "C" washer 22A319 - both these parts wear as well as the gear. Now made 2 thou oversize to help corect wear issues.
Only f...
Proper timing of the camshaft is very important and while it is easy and nice to do it with a precise adjustable cam sprocket it is also cheap to do it with offset cam keys. 1 or 2 degrees difference in cam timing can make a difference in performance...
3 compression ring @ 0.625" oil ring 0.125 as per original 998 pre A plus and 1098cc versions inc morris minor and sprite range.
Genuine Mini Spares green and black upgraded Klinger gasket set. 3 pieces
Has the extra front gasket required for 3 synchro case use
Emission hose from carb to breather valve, this hose has special size ends and made of a material to cope with taking these emission gases.
Approx 23.75" long with internal 5/16" end and 1/2" other end.
GHC406 jubilee c...
These can get really cooked behind the exhaust manifold, if you're oozing oil it may be time to replace them. Sold singly 2 required per engine
For high performance engines an efficient crank damper is a necessity to reduce failure. The standard damper commonly used is barely adequate for the standard engine. Mini Spares has reproduced the original "S" damper and pulley-far superior to the s...
Original short pin drive oil pump for all Pre A Plus minis with 850/998/1100cc engines except autos and others with star drive or the later slot drive pumps as found on A Plus blocks.
The special washer under the tappet cover bolt.Sold singly 2 required per engine.
See 12A1176 for seal
Good maintenance, just as you would never rebuild your motor without replacing the crank thrust washers, you should also care about the camshaft thrust plate. Sometimes called the "triangle plate" this small but important plate doesn't just hold the ...
Cup type core plug for all A plus and 1275cc engines except for Cooper S. 33.6mm wide.A plus 5 required but only 4 on 998 A plus. 1275 has 2 core plugs oil pump end of block whereas 998 only has one
Genuine Mini Spares best selling super upgraded Klinger gasket set for any popular engine block.
So called genuine Rover gasket sets were so poor in quality or have incorrect parts we decided to put together our own correct real gasket set u...
Tappet chest cover seals for all small bore and Cooper S engines (except pre 1966 which use 12A1139). Quantity required-2 per engine.
This latest type washer with internal seal is used on the oil feed pipe from the block to the filter. One either side of the pipe union. Found on engines from about 1985 on. Sold singly, 2 per car required.
3 Bolt hole fixing pump for A plus 998cc engines. This has a spade type drive spindle to fit the slot in the camshafts. This replaced earlier peg type drive which fitted into camshafts with a pin (known as pin drive).
Genuine Timing cover Klinger gasket with screen sealant strip to stop leaks for cars with timing chain tensioner bulge as standard on all A Plus.
Definitely worth the extra cost for longevity on your valuable classic mini
Tip-When ...
Unpainted crank pulley for high performance engines, an efficient crank damper is a necessity to reduce failure. The standard damper commonly used is barely adequate for the standard engine. Mini Spares has reproduced the original "S" damper and pull...
New competition valve cotter, these are precision CNC machined from 4340 and heat treated to a better spec than EN24T and claimed to be stronger in fatigue life.
These locate better in the valves and easier to control spring heights.
Upgraded rocker cover gasket made in silicon, cut outs for 11 stud head and ideal when rocker cover is removed on a regular basis.
Rarely you may require longer rocker cover bolts when fitting this so use CAM6823.
Spring seat shims (set of 4), .030 thick (0.76mm).
Spacer shims to increase valve seat pressure and overall spring rate.
These were also used on all the 8 port head valve seats to prtect the alloy seats from wear. (8 port now C-AHT3...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.