GEARBOX TO BLOCK GASKET SET - GENUINE MINISPARES
GUG703049SG

£4.50 exc vat

£5.40 inc vat

In stockIn stock
Genuine Mini Spares green and black upgraded Klinger gasket set. 3 pieces



Has the extra front gasket required for 3 synchro case use

£4.50 exc vat

£5.40 inc vat

In stockIn stock

Recommended usage 1 x GUG703049SG to fit one mini.
Power Unit Gasket Sets 1959-2000 - Qty 1
Gearbox Transmission Case - Qty 1

Recommended products

Small O ring that fits between engine and gearbox mating surfaces to ensure oil pressure flow, so dont ever leave this out and always renew it whenever possible.

Popular bumper to overider bar bolt but also fits oil pumps and gearbox cases. 1.5" long bolt.

Following are oil pump bolt lengths.

GFK5170 is 1.5" long Holburn Eaton and Sureflow.

BH604131 is 1.6250".

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

Alternative products

The gasket with the oil suction seal hole fits every mini gearbox case and the other two are for the different case shapes, one for 3 synchro case and one for 4 synchro gearbox case, so choose the one you require. For latest spec Klinger gasket set u...

People also bought products

This is the large seal for the early type oil filter assembly pre spin on type.

Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.



Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...

Originally developed by Rover to cut down on warranty hourly costs on powertrain warranty repairs, by their main dealers.-Labour time allowed at Rover dealers for fitting this seal was 3.4 hours labour rate.

This is a special rigid seal and ...

The gasket with the oil suction seal hole fits every mini gearbox case and the other two are for the different case shapes, one for 3 synchro case and one for 4 synchro gearbox case, so choose the one you require. For latest spec Klinger gasket set u...

Genuine Mini Spares Klinger timing chain gasket for any BMC A series engine with 10 gasket holes, fitted until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.

The klinger m...

Genuine gearbox gasket for the large alloy end cover which also houses the speedo drive pinion for all years of mini. The small gasket on the alloy housing with 2 bolt holes is GUG705564GM and the small pear shaped speedo housing gasket ...

Non genuine water pump gasket for all A series engines.

Mini Spares Non genuine timing chain gasket fitted to every BMC A series engine with 10 gasket holes until the introduction of the A plus type which had a bulge in its side where the tensioner was fitted which had 11 holes.

Gasket material h...

Mini Spares quality gasket. When the factory introduced a timing chain tensioner to single row chains on the A plus engines they had to change the shape of the front plate giving it a bulge. This is the gasket for A plus engines only.

Lower differential housing paper gasket for old magic wand and remote type gearboxes, rod change gearboxes.

Gearbox oil strainer to gearbox internal case gasket and also used on the C-AHT54 special oil pick up pipe. One also sits on the outer plate held onto the gearbox outer casing by 2 screws.

Mini Spares own Gearbox gasket set for all manual Mini transmissions. It does not include the clutch oil seal 13H2934 or output shaft seals ADU5738 or 13H577 selector shaft seal for pre rod change gearbox becaus...

Probably the most used jointing compound used by mini owners for nearly every gasket except the cylinder head. Some late minis used a silicone jointing compound instead of gaskets on the differential, see GAC8000.

for the inspection plate on the front cover of the transmission where the speed cable goes to -it has 2 bolt holes cut out

The upper differential housing gasket for all minis. The lower gasket for rod change gearboxes is 22G1836 and for remote use 2A3506B.

Gearbox output shaft housing gasket for all minis except auto.

Sold singly 2 required per gearbox.

These can get really cooked behind the exhaust manifold, if you're oozing oil it may be time to replace them. Sold singly 2 required per engine

genuine block gasket set for 1300 without tappet chest seals or clutch seal

Mini Spares own Universal gasket set for solid wall blocks

For any manual block, includes gaskets for "A"Plus and pre A Plus timing covers, but is less tappet chest cover gaskets. Does not include clutch oil seal.

We now offer an en...

Engine front plate gasket for any A series units pre A Plus.

For A plus see GUG705554GM or CAM4700B.

For a superb quality engine block gasket set see GUG701614CS