CLUTCH OIL SEAL UPTO 1992
13H2934

£1.85 exc vat

£2.22 inc vat

In stockIn stock
See 13H2934MS for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems.

This seal is the standard aftermarket item and adequate for standard use.

Fits every mini except automatic but in 1992 the factory replaced this with LUF10005 which were meant to be more impregnable against crank pressure build up but racers still prefer our 13H2934MS. All are interchangeable. It is also worthwhile fitting the plastic protector shield DAM2821 fitted as standard to engines with verto clutch.

a clutch tool CE12 is recommended to fit seal without damage

£1.85 exc vat

£2.22 inc vat

In stockIn stock

Recommended usage 1 x 13H2934 to fit one mini.
Clutch Housing - Qty 1
Clutch cylinders and flywheel case - Qty 1

Recommended products

Two part primary gear oil seal tool (known as clutch seal tool). It includes the sleeve that slides over the primary gear to protect the seal membrane on the gear splines, plus the outer body that pushes the seal home square. This is achieved by usin...

When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...

Alternative products

Genuine Mini Spares product in Viton.This oil seal was introduced in 1991 with the first injection models and the HIF38 carb version cars and has the internal spring closer to the back. Meant to help with extra crankcase pressures and nips up slightl...

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

Kit products

Full rebuild kit less diferential parts with competition layshaft.

Using only the original manufacturers of the bearings, such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a ...

Full rebuild kit with diferential parts with standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit less diferential parts with competition layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a f...

Full rebuild kit with diferential parts with competition layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a f...

Full rebuild kit less diferential parts.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full kit of bearings except...

Full rebuild kit less differential parts, supplied with standard layshaft

Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use.

This...

Full rebuild kit with dihferential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit less diferential parts using standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a ful...

Full rebuild kit with differential parts and standard layshaft.

Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.

This is a full...

Full rebuild kit less diferential parts with competition layshaft and EVO baulk rings.

Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. <...

People also bought products

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...

Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use [link]...

Gasket used under the dual master cylinder brake master cylinder. For the earlier single line brake pipe system see 31G279.

Clutch arm return spring for the return of the slave cylinder push rod. Total length 90mm.

Made in EN24T for strength they have been made to fit the majority of flywheels that seemed to slightly differ from the mid 60s. Run a file down the raised keyway if tight. This flywheel locking plate is for pre verto diaphragm clutches. For Verto ty...

This plate is on the end of the PRE A plus original long type clutch arm 22A2204 to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518.

If you have the later Mini Spares arm...

Clutch release plunger-This is the carrier that holds the clutch release bearing and on the other end has a hole for the clutch lever arm 22A2204MS.

If you are looking for a Mini Spares upgraded product see 22A180.

1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.

This gasket sits under the clutch master cylinder.

For brake master cylinders see 31G840.

The large special shape nut on the adjusting end of the clutch plunger which holds the release bearing. The flat locking nut for this is NT610041. need a 15/16 spanner

A great deal of the torquing action of the engine is taken up by the stamped metal bracket that bolts to the firewall. A symptom of this is a sharp clunking sound from that area when you accelerate or decellerate. The ugly fix is to weld a large wash...