CLUTCH BOLT LONG COVER TO PRESSURE torque to 16lbs...
2A3657

£2.09 exc vat

£2.51 inc vat

In stockIn stock
Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use C-2A3657 for anything other than standard as this is flanged and in high grade material.

£2.09 exc vat

£2.51 inc vat

In stockIn stock

Recommended usage 3 x 2A3657 to fit one mini.
Diaphragm Clutch & Slave Cylinder - 1964 ON - Qty 3

Recommended products

These are the straps held on by 2A3659 bolts on the diaphragn type flywheel.

There are 2 per bolt making 6 in total as standard but on performance flywheel and clutches we recommend 3 straps per bolt to minimise stretching.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

Alternative products

Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...

Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof wa...

People also bought products

Pre verto flywheel bolt and keyway washer in EN24T



The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.

Fitting kit for 22A2204MS clutch arm with a square end. The plate to fit on the end of the arm in this kit is 20mm wide at both ends see 2A3601MS but earlier arms used 25mm down to 20mm wide see 2A3601.
<...

Plate on the end of the PRE A plus long type clutch arm 22A2204MS to hold the return spring 1G5999. The clevis pin to hold this on the arm is CLZ518--this is the square type but for earlier tapered type Rover ar...

Pre verto race quality tuftrided clutch arm kit made in EN24T for any heavy duty diaphragm- special design plunger with arm to suit, hardened clevis pin and R-clip included.

Race quality bolt-sold seperately- these shorter bolts hold the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof wa...

Race quality shoulder bolts for the Mini clutch backplate to the diaphragm--sold seperately- heavy duty racing type EN16 tightenn up to 16lbs per sq foot torque when using shake proof washer or 18lbs and locktite. Use with C-2A3659 race ...

Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}

Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.

Heavy duty clutch release bearing with a wider surface area, helps to spread even pressure on the clutch diaphragm and is favoured by racers.



small face with numbers stamp-face outwards, larger surface aera side face flywheel.

Anchor tab for return spring that fits behind bleed valve on Slave cylinders, for Pre Verto clutches.

Upgraded pre verto clutch lever arm plunger. Surely to be copied by competitors as the early diaphragm clutch really needed a quality item to be remade. This is the carrier that holds the clutch release bearing and on the other end has a hole for the...

Introduced for competition engines where the increased rev limits or temperature can cause the LUF10005 or 13H2934 to leak, this fits all minis except automatic. This is Mini Spares copy of the original gaco seal and is iden...

Performance type Verto 180mm wide paddle type drive plate as used for racing.

Alternative to AP Racing plate

Mini Spares Performance clutch plate.

Great upgrade for increased performance engines,tested to 10,000rpm and to destruction for evaluation.

For diaphragm type clutch, pre verto. Great clutch plate and a better priced alternative t...

Borg and Beck Clutch Plate,upgraded when fitted to ERA Turbo,great plate for lightly tuned cars from 850-1275cc.

Upgrades after this are C-AHT595 which is ideal for any std road use on 1275cc and C-AHT596 from AP r...

Clutch diaphragm, blue for 1275/1100/998/850 Mini, pre Verto.

This part superseded the GCC102 850-1100 diaphragm.

The bolt that holds the flywheel to the crank on cars with a diaphragm type clutch. Locked in place by 22A1155 locktab on the 88G508 key washer.

There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.

Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...

AP Racing 4 finger type race plate which is also what AP have decided to use to replace their old style 6 sintered pad type. See our our 5 finger type C-AHT597. This is AP Racings only sintered plate which was used for heavy duty racing ...

Steel Road weight 4.87lbs( 2.211kg) Pressure plate for diaphragm type clutches.

Now same uprated material and design of C-AHT230-

Great alternative and upgrade for the obsolete Cooper S and std mini type backplate for ...