£3.55 exc vat
£4.26 inc vat
In stock
The factory changed the seal in 1992 to the type with the spring close to the back which has been known to slip off.
a clutch tool CE12 is recommended to fit seal without damage
£3.55 exc vat
£4.26 inc vat
In stockRecommended usage 1 x 13H2934MS to fit one mini.
Two part primary gear oil seal tool (known as clutch seal tool). It includes the sleeve that slides over the primary gear to protect the seal membrane on the gear splines, plus the outer body that pushes the seal home square. This is achieved by usin...
When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...
See 13H2934MS for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems.
This ...
Genuine Mini Spares product in Viton.This oil seal was introduced in 1991 with the first injection models and the HIF38 carb version cars and has the internal spring closer to the back. Meant to help with extra crankcase pressures and nips up slightl...
Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS
Using only the original manufacturers of the bearings such as RHP because all t...
Pre verto flywheel bolt and keyway washer in EN24T
The bolt is CNC machined from stock EN24T steel with extra attention to the radius under the head to maximise strength.
Clutch housing bolt to engine long 5/16" UNF 1.75" long with tuflock patch to secure. Earlier bolts less tuflock are {link]BH605141{/link}
Flanged head short UNC 5.16" BOLT for flywheel casing 1.0625"long it was used as an alternative to DAM7755 which was only 1" Long with tuflock patch to secure-this will be discontinued by Rover when current stocks are gone.
There are 3 of these shorter 5/16"unf bolts holding the spring straps 2A3658 to the flywheel on diaphragm type flywheels only. Not for Verto flywheel.
Only tighten up to 16lbs per sq foot torque when using shake proof washer or ...
When the verto clutch was introduced the factory started fitting this plastic protector over the clutch oil seal on Metro's. It then apeared on injection minis with LUF10005 clutch seal to the end of production. Should be replaced when s...
Shouldered 5/16"unf bolts for the Mini clutch backplate to the diaphragm, not for heavy duty use or racing. Only tighten up to 16lbs per sq foot torque when using shake proof washer (GHF323) or 18lbs if using flat washer and locktite. Only use [link]...
Gasket used under the dual master cylinder brake master cylinder. For the earlier single line brake pipe system see 31G279.
Clutch arm return spring for the return of the slave cylinder push rod. Total length 90mm.
Made in EN24T for strength they have been made to fit the majority of flywheels that seemed to slightly differ from the mid 60s. Run a file down the raised keyway if tight. This flywheel locking plate is for pre verto diaphragm clutches. For Verto ty...
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
This gasket sits under the clutch master cylinder.
For brake master cylinders see 31G840.
The large special shape nut on the adjusting end of the clutch plunger which holds the release bearing. The flat locking nut for this is NT610041. need a 15/16 spanner
See 13H2934MS for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems.
This ...
A great deal of the torquing action of the engine is taken up by the stamped metal bracket that bolts to the firewall. A symptom of this is a sharp clunking sound from that area when you accelerate or decellerate. The ugly fix is to weld a large wash...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.