£227.82 exc vat
£273.38 inc vat
In stock
Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use.
This is a full kit of bearings except the 2 rollers under 1st and 2nd gear which often do not get checked(available as AAU1815-AAU1816). Complete set of gaskets and seals for rebuild and fitting back to engine-baulk rings and new layshaft,
with idler gear bearing for case this kit is for remote and pre A plus rod change gearbox only with 14mm thick mainshaft bearing where 1st motion shaft fits. If you want to do the diff as well use MSG17
£227.82 exc vat
£273.38 inc vat
In stockRecommended usage 1 x MSG16 to fit one mini.
Genuine RHP Outer support bearing for the first motion shaft. Comes with bearing and outer race. You MUST REPLACE the outer race when using the new bearing. An easy way to remove the old race is to clean the housing very well, remove the circlip, and...
Pre A plus 4 synchro laygears had 2 of these fitted plus a small bearing whereas the A plus laygear had only one.
See 13H2934MS for original silicon type best seal available, which is Mini Spares own copy of the original Gaco seal that was discontinued. These were the seals used on production/rally /race cars that never gave problems.
This ...
Genuine RHP bearings. Not cheap Imported rubbish as sold under this part number.
This is the workhorse of the Mini gearbox. This double roller bearing supports the shaft where it transmits the power to the wheels. When this bearing goes, the...
Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
Upgraded version in Viton available us ADU5738VITON
When in doubt replace it. You have heard this many times but you better believe it on this part. If you have not personally just replaced these layshaft bearing then do it now while you have the chance. These bearing will destroy the inside of a very...
Bearing 26.9mm wide to take 19.05mm idler gear shaft that fits in the gearbox case and clutch housing case on 4 synchro gearboxes until introduction of A plus when a larger bearing was fitted.
This little roller bearing goes inside the end of the 1st motion shaft on minis with 14mm mainshaft which it sits on.
This bearing was previously part number 88G409 and a true Rover replacement, but if you have earlier A type gears with the...
Genuine 1ST Motion shaft SINGLE track original bearing for 4 synchromesh 1st motion shaft.
This is a Genuine RHP bearing, and should not be confused with cheap alternatives. The cheap aftermarket bearings often fail and the work involved to...
Mini Spares genuine part, made for reliability, because the current Rover 22G2033version is not good enough. These specials are CNC grooved for correct shape and machined for concentricity using the original type fixings to get the corr...
Full rebuild kit less diferential parts with competition layshaft and EVO baulk rings.
Using only the original manufacturers of the bearings such as RHP because all the budget bearings are not good enough for longevity or performance use. <...
Full rebuild kit with diferential parts with competition layshaft, our 22G2033EVO baulk rings and performance clutch oil seal 13H2934MS
Using only the original manufacturers of the bearings such as RHP because all t...
Full rebuild kit with differential parts and standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Full rebuild kit less diferential parts using standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a ful...
Full rebuild kit with dihferential parts and standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Full rebuild kit less diferential parts.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full kit of bearings except...
Full rebuild kit with diferential parts with competition layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a f...
Full rebuild kit less diferential parts with competition layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a f...
Anybody proud enough to still be driving around with their 3 syncro gearbox needs all the encouragement they can get! We are pleased to be able to still provide these to keep the car alive and feeling like new. The shift forks are made of a brass t...
Attaches to the rear subframe with clevis pin CLZ549 to route the handbrake cable to the rear drum. These often seize up stopping correct braking as picked up on MOT tests. For dry rear suspension subframes only.
2 fitted to tak...
Full rebuild kit with diferential parts with standard layshaft.
Using only the original manufacturers of the bearings such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a full...
Full rebuild kit less diferential parts with competition layshaft.
Using only the original manufacturers of the bearings, such as RHP because all the Budget bearings are not good enough for longevity or performance use.
This is a ...
Upgraded Viton version of ADU5738. Drive shaft oil seal or diff output shaft oil seal for all Mini's except Cooper S and early Automatics. 2 required per gearbox.
UK made straight cut PRE A PLUS gear kit includes 1st, 2nd, 3rd gear, 1st motion shaft, reverse gear and laygear for remote change. Please order genuine C-22A1741 or 22G2033EVO baulk rings when fitting this gear kit. These are the original ratio and ...
The Swiftune classic Mini Quaife ATB Automatic Torque Biasing differential offers the benefits of an LSD limited slip differential but saving you money on crownwheels and pinion plus output shafts!!
The Swiftune Quaife ATB avoids the need fo...
Left hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used. For R/H locktab see 22A962
Right hand differential lock tab as used on rod change boxes up until 1982 when they were not longer used.
Mini Spares best quality complete gasket and seal kit for engine block and gearbox,for all common engine types and sizes.
Also comes complete with Mini Spares Evolution clutch oil seal 13H2934MS, differential oil seals...
This unit fits directly on to the gearbox in place of the standard cable and produces a digital signal for use with any electronic speedometer requiring 12 or 5 volt square wave pulse such as our electronic speedo 13H4443. For pre 1980 s...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.