£4.50 exc vat
£5.40 inc vat
In stock
£4.50 exc vat
£5.40 inc vat
In stockRecommended usage 1 x GCS119 to fit one mini.
If you have a red distributor cap (GDC214 its likely that you have a Ducellier distributor and these is the rotor arm for it.Contact set is GCS119 and the condenser is GSC2113
Lightweight billet aluminium distributor hole blanking plug for A+ engines.
Lots of things have been written about performance plug ignition wires but regardless of what you believe we all know that good wires are a must. This special competiton wires set from the Lucas factory has 8mm wire and the highest performance, no br...
original Lucas type RESIN BASED CONDENSER made for the 45/59D type distributor if you want a quality item rather than the cheaper inferior parts available. Filled with 3m of winding inside as per original Lucas but every copy analysed to date has ...
RESIN BASED CONDENSER as per the original Lucas type made for the 23/25D type distributor as fitted to original Cooper S or Racers who want a trusty part or where originality is required,with soldered wire connections and correctly made foot to sit ...
Electronic Distributor for any standard A+ 998cc. Negative earth only.
From 1982on 998cc were fitted with a ballast coil which means a new wire must be fitted from fusebox top left terminal where there is a large white cable to the...
These are the screws needed to fix the condensor, points, base plate and vacuum to 45D and 59D distributors. For 23/25D type see 17H5106
These are the screws needed to fix the condenser, points and base plate to 23/25D distributors. See 57H5135 for 45D type distributors.
Replacement distributor cap retaining clip for all 45D type distributors-sold per clip.
Electronic Ignition distributor, fitted as standard to all 1300 Carb Cooper models. Also Metro 1275cc engine.
Replacement service items for this are:
Cap GDC156
Rotor arm GRA2143
Should be used with GC...
Replacement Distributor ignition module fitted to all standard electronic ignition distributors (non injection) looking at the front of module, negative is on the left. positive on right and centre pin is not used.
the oil seal to fit on 12A1136 distributor housing. Pre A Plus
the earlier housing 2A612 did not have a seal.
If you have an original 25D type distributor this is an upgraded arm (blade moulded and riveted )for performance use because all the other types available now are likely to fail at high revs. Because the blade is thin,or the rivet sometimes to long a...
A favourite for specials where room is at a premium and easy access is required for 45D type distributors only--uses GRA2128 rotor arm and obviously discard screws from cap and use existing distributor clips to secure.
some caps...
Rotor arm for all A series electric distributors when points are not fitted, except for turbo. The distributor cap for this rotor arm is GDC156.
The O ring that actually sits on the distributor drive spindle shaft in the recess provided.
This was the first mini distributor cap to have screws hold the cap to the body from about 1990 on, when electonic ignition was introduced. Therefore there is no points or condenser but the rotor arm to use is GRA2143. Fits all 1992 onwa...
The stock vacuum advance distributor is connected to the carb/manifold by a small rubber joint that in turn is mated to metal line that fits the distributor. If the little rubber connector is deteriorated it could allow a vacuum leak at the carb and ...
The original blue rotor arm was fited with a blue cap GDC143 to the turbos and were made stronger by moulding and riveting the contact plate to the arm, so if you are looking for an upgrade on your 45D body distributor this is our altern...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.