£10.85 exc vat
£13.02 inc vat
In stock
£10.85 exc vat
£13.02 inc vat
In stockRecommended usage 1 x HMK31K to fit one mini.
As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.
These pipes are retail...
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve. fits in the bottom union and goes to left hand union in valve (to go to rear brakes)
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve
As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
Easy bend copper brake pipe 26" long with one female and one male end - used on hydrolastic cars from regulator valve to near side rear hose. These pipes are retail less 35% discount at least to keep prices viable.
Easy bend long life copper brake pipe with 2 male ends and ideal and best replacement for the original 16" pipe from the 3 way union to the brake switch on single line dry suspension minis. These kits or pipes are at least 35% off retail.
UNION FOR BRAKE PIPES IF YOU HAVE A DO IT YOURSELF FLARING KIT.
Set of 5 braided hoses. 2 front brakes, 2 rear brakes, and clutch hose for pre A+.
If it is time to replace the brake lines on your Mini, and it probably is, you should consider replacing them with braided-steel hoses. They are direct bolt...
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis. These kits or pipes are at least 35% off retail.
Servo to 3 way on Cooper S R/H/D and L/H/D except 1275GT(30" HF32)-Easy bend copper brake pipe 24" long with 2 male ends. These pipes are retail less 35% discount at least to keep prices viable.
Front to rear brake pipe, 104" in length. Includes male fittings on each end. For long wheel base Minis.
Copper easy bend 10" long metal pipe with male and female end fittings to fit between rear wheel cylinder and flexible hose on dry suspension models. These pipes are retail less 35% discount at least to keep prices viable.
1.4mm thick copper washer for all clutch and brake joint uses. This washer is 17.4mm wide with an 11.4mm diameter hole. Larger than a 233220A.
This Genuine AP 3 way connector was used on the diagonal split braking system joining the front brake pipes to the main line system on both sides of the car, hence 2 fitted. On later dual line cars, with the pressure valve on the bulkhead (1978 on), ...
Copper easy bend 6" long with a female and male end for fitting from the regulator valve on the rear subframe to the hose on the right hand rear. Dry suspension cars only as the hydrolastic uses HD8. Also used on late front to rear split...
Brake line from RH brake hose union to the LH brake hose. 44" in length.
Also master cyl to servo for L/H/D which was 43" long.
Master cyl to servo for rhd 30-32". Also brake line for master cylinder to "T" on LHD models. 32" in length. Also clutch master cylinder on L/H/D (usually 32-34" long) but this easy bend pipe will fit all. These pipes are retail less 35% discount at ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.