£9.15 exc vat
£10.98 inc vat
In stock
£9.15 exc vat
£10.98 inc vat
In stockRecommended usage 1 x HD6 to fit one mini.
Conversion kit when converting rear subframe from hydrolastic to dry, includes everything except dry subframe radius arms and dampers owing to different customer requirments.
*** Please note: Radius arms are NOT included in this pa...
Rubber gaiter to keep debris from entering the drum via the backplate handbrake lever SMN10005. Sold singly per backplate, 2 required per car.
Genuine AP Lockheed rubber boot
Set of 4 hoses, 2 front and 2 rear.
Braided brake and clutch hoses have a PTFE inner which helps to eliminate the spongy pedal feel under arduous conditions, and give greater efficiency. The outer braided stainless steel cover e...
NICKEL copper easy bend brake pipe with 2 metric male unions. 22"long, for 1988 on master cylinder lower outlet to PDWA valve outlet nearest to wing-other pipe is HMK026-both for left or right hand drive.
These pipes are retail...
We now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve. fits in the bottom union and goes to left hand union in valve (to go to rear brakes)
Brake pipe with male metric ends, 12mm for master cylinder and 10mm for PDWA valve
As the original brake pipe kit is now obsolete, we now supply 2 easy bend copper nickel pipes with the correct unions for when converting to the later type GMC227 front to rear split master cylinder.
One male and one female end on a copper easy bend brake pipe 106" long
Die cast alloy brake drums with built in spacer-imported copy but have proven 100% reliable on sales from 1998 without any problems. The alloy material has a finned design that dissipates heat quicker which in turn helps reduce brake fade. While desi...
Brake pipe connecting piece originally used on diagonal split system.1.25" long
Pre bent steel brake pipe for the rear regulator to the RH flexi hose. Please note this will only fit cars with a regulator valve not a T piece on the rear subframe as the flare is different.
Single line L/H/D with servo-dry suspension. If you have a drum brake mini then this kit will require 2 front wheel cylinder to wheel cylinder pipes HF10
All MK3 minis to 1978 except Cooper S MK3 which used 21A1774.
Fitted mainly to cars with 3/4" larger bore rear wheel cylinders.
The correct regulator valve for all MK1/2 mini plus all Cooper S inc MK3 is 21A1774 where m...
Genuine AP brand new rear Left Hand back plate assembly (beware of copies).
These are ready to bolt on, brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder ...
Genuine AP brand new rear right hand back plate kit (beware of copies).
These are ready to bolt on brand new stock from AP Automotive and have the .75" bore genuine wheel cylinders GWC1102. Remember that all wheel cylinder rubb...
Adjustable original brake proportioning/balancing valve for racers only.
The most common brake system on the Mini has Disc brakes in the front and drums in the rear. The weight bias on the car is all in the front and thus under hard braking...
Easy bend copper 12" brake pipe with 2 male ends for single line master cylinders---for clutch or brake on early minis but the longer HF14 might be easier for the brake master which was nearer 13" long. These kits or pipes are at least 3...
Front to rear brake pipe, 101" in length. Includes male fittings on each end. Some early dry cars used a 103" pipe.
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.