£140.00 exc vat
£168.00 inc vat
now
£119.00 exc vat
£142.80 inc vat
In stock
£140.00 exc vat
£168.00 inc vat
now
£119.00 exc vat
£142.80 inc vat
In stockRecommended usage 1 x HMP441005 to fit one mini.
floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...
L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Commercial Mini floor extension
It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad
floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...
Floor pan front to rear for the right hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mult...
Genuine front panel fits all pre rubber mounted subframe cars .
The early pre 1964 Mk1 had different shape lower valance without cut aways under the bumper apron but this genuine panel will fit all.
There is a good aftermaket panel...
Inner front R/H wing with the A panel and door stiffener check strap panel attached for ease of fitment and alignment. Always check the bonnet prop bracket location as they changed.
This late front panel will fit any Mini, with rubber mounted subframes, manufactured after 1976. It is probably easier to replace the entire panel than to repair a damaged one, especially if it's been hit more than once. Early Minis can use [link]MS4...
Aftermarket version of the R/H floorpan for 1992 on cars.
This floor was made stronger to prevent vibration and rust and will fit any Rod change gear shift mini started on the first injection cars
Right hand inner wing section only for MK3 cars with 3 air vent holes. One with 4 bolt holes,one with 4 castellated bolt holes (nuts welded in place) and one large trunk hose hole at front. If you want the same panel with A panel combined for better ...
lower section known as front panel for the clubman range only.his is the rubber monted subframe type as fitted from 1976 on-the earlier type which bolted direct to the subframe is CZH563
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen a...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.