£145.00 exc vat
£174.00 inc vat
In stock
the front of these panels is the same but the subframe mounting bracket on the rear is different
£145.00 exc vat
£174.00 inc vat
In stockRecommended usage 1 x CZH563 to fit one mini.
lower section known as front panel for the clubman range only.his is the rubber monted subframe type as fitted from 1976 on-the earlier type which bolted direct to the subframe is CZH563
Really a built up half front end for the mini clubman, consists of a lower panel with headlamp panels,slam panel and stiffener between the front and slam panel,
but not inner or outer wings
L/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
R/H Inner hinge type A post repair panel with hinge fitting holes mini, MK3
this is a genuine heritage part.
This Non genuine pattern panel has the holes for windscreen wipers and jets with barely an inch of pillar.
On cars from 1992/3 on check the original windscreen drain channel as the VIN numbers were stamped above the clutch master cylinder-wi...
Commercial Mini floor extension
It is an essential part for the correct restoration of all the longer wheelbase mini derivatives. From the original tooling.
The only bonnet landing panel available for the clubman shape body for a long time this part is perfect in every detail and was used on the heritage bodyshells.
A Genuine panel is now available from BL Heritage CZH149.
...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation and fairly well represent the original stamping. They have added metal to include...
You can spend hours cutting out rust and patching holes, but why bother? These reproduction floor pans extend the full width with vertical flanges for easy installation, and fairly well represent the original stamping. They have added metal to includ...
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section of inner wing
If your rusted old headlight bucket is getting to you, don't waste time trying to salvage it when new metal reproduction metal buckets are AVAILABLE.
With a headlamp rim fixing bracket 37H7421 attached
Whether you are ...
1970 on, cars with internal hinges and wind up windows
This repair panel has holes for the hinges on A post and overlaps 3.5"(85mm)onto the wheel arch section
This panel has mounting holes for later models facia crash panel. These holes will require blanking for true originality on earlier models without the facia pad
floor pan front to rear for the left hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mul...
Floor pan front to rear for the right hand side only to the correct floor shape before 1990-1 rib design change---ideal for MK1/2 restoration with original 4 flute indentation. This has the carpet stud brackets plus underside slinger bracket and mult...
See ALA5661MS for an upgraded thicker and best fitting aftermarket L/H A panel-all the local bodyshops fit this.
Known as an A panel this is for all wind up widow type cars with internal door hinges and is single skin as opposse...
A non genuine panel made for repairing the corner of the windscreen panel which is prone to rust from water splashing up from underneath the front wheel arch.
Experience has shown its easier to fit the genuine panel HMP441001 al...
Genuine panel that has the holes for wipers and jets with only a few inches of pillar which is basically the area that rots. Also referred to as the windscreen scuttle lower panel. Fitting the genuine type ensures you should get a better windscreen a...
Fits round tunnel cars. Approximate location of the vertical, forward wall is 17.5 - 17.75 inches back from the crease in the floor where the floor bends upward under the pedals. The forward wall lines up just forward of the front portion of the exte...
THIS PANEL PROTECTS THE UNDERSIDE OF THE WINDSCREEN VALANCE UNDER THE FRONT WING SECTION also fitted on the inner wing panel 14A8346/7
For Minis with sliding windows and external door hinges. These NON genuine R/H outer A panels fit over the extra inner panel which have brackets on to reinforce the exterior hinges. If the outside one is rotten you can guarantee ...
Contact Us| About Us| Terms| Switch to main website
Copyright @2014 Mini Spares. All rights reserved e&oe.